Roland SP-404MK2 - Page 129

Appendix
129
While holding down
the [SHIFT] button
Function Explanation
→
“Setting the Tempo in Time with the Rhythm (Tap Tempo)(P.76)”
Pad [12]
GAIN
Displays the UTILITY MENU > SYSTEM > GAIN tab.
→
“GAIN(P.110) tab”
Pad [13]
UTILITY
Displays the UTILITY MENU screen.
→
“Configuring the Various Settings (UTILITY)(P.91)”
Pad [14]
IMPORT/EXPORT
Displays the UTILITY MENU > IMPORT (IMPORT/EXPORT MENU).
→“Importing Samples (IMPORT SAMPLE)(P.101)” “Exporting Samples
(EXPORT SAMPLE)(P.102)” “Importing a Project (IMPORT PROJECT)(P.103)”
“Exporting a Project (EXPORT PROJECT)(P.104)”
Pad [15]
PAD SETTING
Displays the UTILITY MENU > PAD SET (PAD SETTING).
→“Configuring the Pad-related Settings (PAD SETTING)(P.92)”
Pad [16]
EFX SETTING
Displays the UTILITY MENU > EFX SET (EFX SETTING) screen.
→“Configuring the Effect Settings (EFX SET)(P.93)”
[REVERSE] button +
Pads [1]–[16]
PAD MUTE
Switches the pad mute on/off.
→“Muting the Playback of a Sample (PAD MUTE)(P.22)”
[BUS FX] button
MUTE BUS
Temporarily turns off the audio sent to the bus (the sample playback sound or
the sound inputted to the INPUT jack), and outputs only the sound of the
effect.
→
“Temporarily Output Only the Effect Sound (MUTE BUS)(P.33)”
[HOLD] button
PAUSE
Pauses the sample that’s currently playing back.
→
“Pausing the Sound of a Sample (PAUSE)(P.25)”
[EXT SOURCE] button
INPUT SETTING
Displays the input settings screen.
→
“Configuring the Sampling Settings (RECORD SETTING)(P.35)”
[SUB PAD] button
PROJECT
Displays the SELECT PROJECT screen.
→
“Selecting a Project(P.83)”
Shortcuts that use the [REMAIN] button
While holding down the
[REMAIN] button
Function (explanation)
Pads [1]–[16]
Sets which sample playback audio is sent to which bus (meaning which effects are used) for
each sample.
→“Deciding on Effects to Use for Each Sample(P.29)”
CH1: Pad [14]
CH2: Pad [16]
(only in DJ mode)
You can set the bus to which the CH1/CH2 sample playback is sent (meaning which effects
are used).
While holding down the [REMAIN] button, each time you press pad [14] or pad [16] switches
the effect to use as follows: “BUS-1”
→
“BUS-2”
→
“DRY”
→
“BUS-1”.
BANK [A/F]–[E/J] buttons
Sets the bus send destination for all samples in a bank.
[MFX] button
Makes the effect edit screen keep displaying.
→“Editing the Effects(P.31)”
[BUS FX] button
You can swap the effects of BUS 1 and BUS 2.
Shortcuts that use the [VALUE] knob
While holding down the [VALUE] knob
Function (explanation)
Effect buttons ([FILTER+DRIVE]–[MFX]
button)
Applies effects only while you hold down the effect buttons (EFFECT GRAB).
→“Turning Effects On/Off at the Desired Timing(P.32)”
[BUS FX] button
Temporarily bypasses BUS 3 and BUS 4.
Pads [1]–[16]
Selects a sample (no sound is produced).
Also, when the [PATTERN SELECT] button is lit, select a pattern (the pattern will
not be played).
Shortcuts that use the [DEL] button