Sanyo PLC-WXE45 - Page 60

60
Picture is not bri�ht enou�h.
– Check if "Contrast" or "Brightness" are adjusted properly (see Check if "Contrast" or "Brightness" are adjusted properly (seeCheckif"Contrast"or"Brightness"areadjustedproperly(see(see
pages31,38)..
– Check if "Image level" is selected properly (see pages 30 Check if "Image level" is selected properly (see pages 30Checkif"Imagelevel"isselectedproperly(see pages 30(seepages30,37)..
– Check the LAMP REPLACE indicator. If it lights, the end of lamp Check the LAMP REPLACE indicator. If it lights, the end of lampChecktheLAMPREPLACEindicator.Ifitlights,theendoflamp
lifeisapproaching.Replacethelampwithanewonepromptly
(seepages57-58,64)..
– Check the Lamp control function (see pages 24, 46). Check the Lamp control function (see pages 24, 46).ChecktheLampcontrolfunction(see pages 24, 46).(seepages24,46).
The color is stran�e.
– Check the Input signal, color system, video system, or computer
systemmode.
– AdjusttheImagelevelproperly(seepages31,38).
Ima�e is Left/Ri�ht reversed.
Ima�e is Top/Bottom reversed.
– ChecktheCeiling/Rearfunction(seepage44).
– ChecktheCeilingfunction(seepage44).
The ima�e is distorted or runs off.
– Check the PC Adjustment menu or Screen menu and adjust them Check the PC Adjustment menu or Screen menu and adjust themCheckthePCAdjustmentmenuorScreenmenuandadjustthem
(seepages26-29,32-33,40).
No sound
– Checktheaudiocableconnectionfromaudioinputsource.
– Adjusttheaudiosource.
– PresstheVolume+button(seepage23).
– PresstheMutebutton(seepage23).
– When the AUDIO OUT is plugged in, the projector's built-inWhentheAUDIOOUTispluggedin,theprojector'sbuilt-in
speakerisnotavailable.
– Is the image projected? You will hear the sound only when the
imageisprojected.
Some displays are not seen durin�
the operation.
– ChecktheDisplayfunction(seepage41).
Auto PC adjustment function does
not work.
– Check the Input signal. Auto PC Adjustment function can not work Check the Input signal. Auto PC Adjustment function can not workChecktheInputsignal.AutoPCAdjustmentfunctioncannotwork
when480p,575p,720p,480i,575i,1035i,or1080iisselected(see
page27).
The settin� does not remain after
turnin� off power.
– Make sure you selected “Store” after adjusting settings. Some Make sure you selected “Store” after adjusting settings. SomeMakesureyouselected“Store”afteradjustingsettings.Some
settingscannotbestoredifnotregisteredwith“Store.”
Power mana�ement function does
not work.
– Power management function cannot work while "Freeze" or "NoPower management function cannot work while "Freeze" or "No
Show"functionisrunning..
Ima�e disappears automatically
– Check the power management function in the Setting. The powerCheckthepowermanagementfunctionintheSetting.Thepower
managementissetto“On”atthefactory.
Capture function does not work.
– Check the connection and the Input signal to see if there is signal.ChecktheconnectionandtheInputsignaltoseeifthereissignal.
The Remote Control does not work.
– Checkthebatteries.
– Makesurenoobstructionisbetweentheprojectorandtheremote
control.
– Make sure you are not too far from theprojector when usingthe
remotecontrol.Maximumoperatingrangeis16.4’(5m).
– Makesure the codeoftheremotecontrolis conformed tothatof
theprojector(seepage46).
Appendix