EasyManuals Logo

Sanyo PLC-XP200L User Manual

Sanyo PLC-XP200L
88 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #31 background imageLoading...
Page #31 background image
31
1
2
Press the MENU button to display the On-Screen
Menu. Use the Point 7 8 buttons to move the red
frame pointer to the Sound Menu icon.
Press the VOLUME+/– buttons on the side control or on the
remote control to adjust the volume of Audio Output. The
volume dialog box appears on the screen for a few seconds.
Press the MUTE button on the remote control to temporarily
turn off the AUDIO OUT. To turn the AUDIO OUT back on,
press the MUTE button again or press the VOLUME +/–
buttons.
Press the Point 7 8 buttons to switch the mute function
On/Off. When the sound is turned off, On” is displayed.
Press the Point 7 8 buttons again to turn the sound back
on.
Use the Point ed buttons to move the red frame
pointer to the desired item, and then press the SELECT
button.
Approximate level of
the volume.
Exit the Sound Menu.
Approximate
level of the
volume.
Press the MUTE button to set the Mute function
On or Off. The dialog box disappears after 4
seconds.
Sound Menu
Sound Menu icon
Volume
Remote Control
VOL + button
VOL – button
MUTE button
Volume (Audio output)
Mute (Audio output)
Press the Point 8 button to turn up the volume; press the
Point 7 button to turn down the volume.
Mute
Direct Operation
Menu Operation
Sound Adjustment
Side Control
Volume Dialog Box
Input pattern
This projector has two INPUT terminals [AUDIO IN I/
AUDIO IN II]. Input pattern allows you to set up INPUT 1,
INPUT 2, and INPUT 3 to each INPUT for sound function.
(pp. 11, 35-37)
Press the SELECT button to display the input pattern dialog
box. Use the Point ed buttons to move the pointer (red
arrow) to the desired pattern and press the SELECT button
to set the input pattern for sound function. Check mark
appears next to the selected Input pattern.
Basic Operation
VOLUME +/– buttons
Input Pattern Dialog Box
Move the pointer
(red arrow) to the
desired pattern
and press the
SELECT button.
Selected Input Pattern

Table of Contents

Other manuals for Sanyo PLC-XP200L

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sanyo PLC-XP200L and is the answer not in the manual?

Sanyo PLC-XP200L Specifications

General IconGeneral
Vertical scan range48 - 100 Hz
Horizontal scan range15 - 100 kHz
Projection technologyLCD
Projector native resolutionXGA (1024x768)
Keystone correction, vertical±40 °
Lamp typeNSH
Lamp power330 W
Light source typeLamp
Service life of light source2000 h
Service life of light source (economic mode)3000 h
Bundled softwareUser Manual (CD ROM)
I/O portsDVI-D (digital/HDCP) D-Sub15 (RGB/SCART-RGB) 5 x BNC (RGBHV/Composite/Y-Pb/Cb-Pr/Cr) 3 x RCA (Video/Y-Pb/Cb-Pr/Cr) Mini DIN 4 (S-Video) 3.5 mm Stereo Jack D-Sub15 D-Sub9 (RS232) 3.5 mm Stereo Jack (cable remote control) USB type B
CompatibilityUXGA SXGA SXGA+ WXGA XGA S-VGA VGA Mac
Dimensions (WxDxH)370 x 440 x 187 mm
Power requirements100 - 240 V
Power consumption (standby)24.5 W
Power consumption (typical)499 W
Storage temperature (T-T)-10 - 60 °C
Operating temperature (T-T)5 - 40 °C
PlacementCeiling
Weight and Dimensions IconWeight and Dimensions
Weight11400 g
Package weight15900 g

Related product manuals