Sanyo PLC-XU115 User Manual

50
Logo PIN code lock
Setting
This function prevents an unauthorized person from
changingthescreenlogo.
 Off ............Thescreenlogocanbechangedfreelyfrom
theLogoMenu(p.49).
 On ............Thescreenlogocannotbechangedwithout
aLogoPINcode.
If you want to change the Logo PIN code lock setting,
presstheSELECTbuttonandtheLogoPINcodedialog
box appears. Enter a Logo PIN code by following the
stepsbelow.TheinitialLogoPINcodeissetto“4321”at
thefactory.
Logo PIN code lock
Enter a Logo PIN code
Use the Point ▲▼ buttons to enter a number. Press the
Point►buttontofixthenumberandmovetheredframe
pointertothenextbox.Thenumberchangesto“.”Ifyou
fixedanincorrectnumber,usethePoint◄buttontomove
the pointer to the number you want to correct, and then
enterthecorrectnumber.
Repeatthissteptocompleteenteringafour-digitnumber.
After entering the four-digit number, move the pointer to
“Set.” Press the SELECT button so that you can start to
operatetheprojector.
If you entered an incorrect Logo PIN code, “Logo PIN
code”andthenumber()willturnredforamoment.
EnterthecorrectLogoPINcodealloveragain.
Change the Logo PIN code
LogoPINcodecanbechangedtoyourdesiredfour-digit
number. Press the Point ▼ button to select “Logo PIN
code change” and then press the SELECT button. The
NewLogoPINcodeinputdialogboxappears.Setanew
LogoPINcode.
Be sure to note the new Logo PIN code and keep it at
hand.Ifyoulostthenumber,youcouldnolongerchange
the Logo PIN code setting. For details on PINcode
setting,referto“PINcodelock”onpages54–55.
Use the Point ◄► buttons to switch On/Off, and then
press the Point ▼ button to move the pointer to “Quit.”
PresstheSELECTbuttontoclosethedialogbox.
Change the Logo PIN code lock setting
Enter a Logo PIN code
AfteracorrectLogoPINcode
isentered,thefollowingdialog
boxappears.
CAUTION:
WHEN YOU HAVE CHANGED THE LOGO
PIN CODE, WRITE DOWN THE NEW PIN
CODE IN COLUMN OF THE LOGO PIN CODE
NO. MEMO ON PAGE 76, AND KEEP IT
SECURELY. SHOULD THE LOGO PIN CODE
BE LOST OR FORGOTTEN, THE LOGO
PIN CODE SETTING CAN NO LONGER BE
CHANGED.
Change the Logo PIN code lock setting
Change the Logo PIN code
UsethePoint◄►buttonsto
switchOn/Off.
Downloaded From projector-manual.com Sanyo Manuals

Sanyo PLC-XU115 Specifications

General

Projection distance	0.93/11.47 m
Vertical scan range	50 - 100 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	LCD
Contrast ratio (typical)	500:1
Projector native resolution	XGA (1024x768)
Keystone correction, vertical	-40 - 40 °
I/O ports	SD Card Slot
Audio input	1
Aspect ratio	4:3
Special features	Soft Carry Bag
Networking features	Ethernet & Wireless
F-number (relative aperture)	1.7
Lamp type	NSH
Lamp power	275 W
Light source type	Lamp
Service life of light source	2000 h
Service life of light source (economic mode)	3000 h
Dot clock scanning frequency	140 MHz
Analog signal format system	NTSC, PAL, SECAM
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Power consumption (typical)	266 W

Weight and Dimensions

Package weight	3500 g