Seatex DPS 200 - Page 69

Seatex DPS 200 Installation Manual, rev. 4 Appendix D - DPS setup file
57
! is the antenna height above the WGS 84 ellipsoid.
! DIFFCORR AGE LIM [s] Maximum age of corrections
! DIFFCORR RANGE LIM [km] Reference station outside this radius are ignored
! The maximum range limit is 10 000 km. If a range limit
! is set outside this limit, 10 000 km will be used.
!
! The parameter HEIGHT AID selects the height aiding mode :
! 0: No height aiding
! 1: Use value of AIDED HEIGHT as constant height
! Recommended ==> 2: Use automatic filtered height aiding. Initial height
! is selected from a preconfigured geoid model, normally
! STANAG 4294. Note that if the correspoindng file
! (Stan4294.GRD) is not found, HEIGHT AID mode 3 is used.
! 3: Use automatic filtered height aiding with AIDED Height
! as initial height.
!
[GPS]
ELEVATION MASK 10
HDOP LIMIT 4
PDOP LIMIT 100
HEIGHT AID 2
AIDED STDV 100.0
AIDED HEIGHT 0.0
DIFFCORR AGE LIM 90
DIFFCORR RANGE LIM 2000
! General GLONASS settings (ignored on DPS 100 systems)
! Same syntax as for GPS settings, but prefixed with GLONASS_
[GLONASS]
GLONASS_ELEVATION MASK 7
GLONASS_HDOP LIMIT 4
GLONASS_PDOP LIMIT 100
GLONASS_HEIGHT AID 2
GLONASS_AIDED STDV 100.0
GLONASS_AIDED HEIGHT 0.0
GLONASS_DIFFCORR AGE LIM 90
GLONASS_DIFFCORR RANGE LIM 2000
!--------------------- DIFF CORR LINK INTERFACE AND DECODING ------------------*
! Stuff for RTCM and SCF decoding
! Comm parameters: nh:no handshake, sh:software handshake, hh:hardware handshake
! DCLNKx NAME A name identifying the link, e.g. SpotBeam
! DCLNKx TYPE options: SCF = Supercompressed format
! RTCM = RTCM Sc-104 v2.2 format
! TOPNAV = DGPS and DVAR from Thales receivers.
! NONE = No input expected (DPS 102 only)
! DCLNKx SHORT RANGE 1: Treat link as a short range link (e.g. IALA)
! 0: Normal operation
! DCLNKx ROLL BYTES options: 0: lsb first 1: msb first (RTCM standard)
! DCLNKx 6 OF 8 BITS BYTE : 0: 8 of 8 1: 6 of 8
! DCLNKx DEBUG 1: debug printout logging enabled 0: disabled
! DCLNKx ENABLE_GLONASS_CORR DPS200 only: 1: enable decoding of GLONASS corrections.
!
! Value of ENABLE_GLONASS_CORR is ignored on DPS 100 systems
!
! Value IONOSPHERE COMPENSATED defines if the corrections are compensated for
! Ionosphere difference between reference station and mobile based on dual
! frequency measurements (ex.g. Fugro's Starfix+ system). Normal here is uncompensated.
!
! Value REF STATION OFFSET reads an offset in x,y,z (north/south, east/west, hight) for the
! reference station position. Some links can deliver differential corrections from reference
! stations measured in a different coordinate system (not WGS84). This offset will compensate
! for such an error.
!
!
FSP ref.: A11213500XRBRA0