EasyManuals Logo

Sharp MX-M464N User Manual

Sharp MX-M464N
843 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #752 background imageLoading...
Page #752 background image
7-82
SYSTEM SETTINGS
Contents
Default Exposure Settings
This is used to set the default exposure settings for
scanning a document in image send mode. Select [Auto]
or [Manual]. When [Manual] is selected, the exposure
can be set to one of 5 levels.
Default Original Image Type
Select the original type beforehand to enable transmission
at a resolution suitable for the original (only in scan mode
and USB memory mode).
The settings are shown below.
• Text/Printed Photo
• Text/Photo
•Text
•Photo
• Printed Photo
•Map
•
Must Input Next Address Key at
Broadcast Setting
This setting is used to require that the [Next Address]
key be touched before the next address is entered when
performing a broadcast transmission.
When this setting is enabled, the [Next Address] key
cannot be omitted even if the next address is entered
with a one-touch key.
If a user attempts to enter the next address without
touching the [Next Address] key, a double-beep alarm
will sound and the entry will be rejected.
Scan Complete Sound Setting
The scan complete sound can be selected.
The Number of File Name/Subject/Body
Keys Displayed Setting
This setting is used to select the number of file name /
subject keys that are displayed in the screen. The
number of keys can be set to 6, 12, or 18.
The Number of Direct Address
Keys Displayed Setting
Select 5, 10, or 15 for the number of one-touch keys that
appear in the address book screen.
Disable Switching of Display Order
This is used to prohibit changes to the order of display
(search number order, ascending, descending) in the
address book.
When this setting enabled, touching a tab on the
address book screen does not change the order. The
display order will remain fixed at the order that is in effect
when this setting is enabled.
Hold Setting for Received Data Print
This function holds received faxes and Internet faxes in
memory without printing them. The faxes can be printed
by entering a password (factory default setting: 0000)
with the numeric keys.
Password
When [Hold Setting for Received Data Print] is enabled,
enter the password (4-digit number).
Default Verification Stamp
(When a stamp unit is installed.)
When the automatic document feeder is used, this
setting can be enabled to have each original page
stamped after it is scanned.
Configure the setting for each of the following items:
• Scan/USB Memory Scan/Data Entry
• Fax/Internet Fax
Erase Width Adjustment
This is used to set the default erase width for erase
function. Specify a value from 0" (0 mm) to 1" (20 mm) in
increments of 1/8" (1 mm) for both edge erase and
center erase.
This is used to prohibit the storing of destinations.
Storing from the machine, storing from the Web page,
and storing from a computer can each be separately
prohibited.
When the exposure is set to [Auto], a default
original type cannot be selected.
These settings can only be configured when there is
no received data in the machine's memory (excluding
data in a confidential or relay broadcast memory box).
Settings to Disable Registration

Table of Contents

Other manuals for Sharp MX-M464N

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sharp MX-M464N and is the answer not in the manual?

Sharp MX-M464N Specifications

General IconGeneral
Print TechnologyLaser
Print Speed46 ppm
Maximum Print Resolution1200 x 1200 dpi
Duplex PrintingYes
Copy Speed46 cpm
Hard Disk Drive320 GB
FunctionsPrint, Copy, Scan, Fax
Print Resolution1200 x 1200 dpi
Scan Resolution600 x 600 dpi
Warm-up Time20 seconds
Max Paper SizeA3
Scanner TypeColor Flatbed
Paper SizeA3, A4, A5, B4, B5
ConnectivityUSB, Ethernet
Original SizeA3
Operating System CompatibilityWindows, Mac, Linux
Standard Paper Capacity1100 sheets

Related product manuals