Siemens MICROMASTER 440 Series - Page 66

International English 5 System Parameters
MICROMASTER 440 Operating instructions
6SE6400-5CA00-0BP0
65
Par. No. Parametername Default Acc WS QC
P2187[3] Upper torque threshold 2 99999.0 2 CUT N
P2188[3] Lower torque threshold 2 0.0 2 CUT N
P2189[3] Upper torque threshold 3 99999.0 2 CUT N
P2190[3] Lower torque threshold 3 0.0 2 CUT N
P2191[3] Belt failure speed tolerance 3.00 2 CUT N
P2192[3] Time delay for belt failure 10 2 CUT N
r2197 CO/BO: Monitoring word 1 - 2 - -
r2198 CO/BO: Monitoring word 2 - 2 - -
PI Controller (P0004 = 22)
Par. No. Parametername Default Acc WS QC
P2200[3] BI: Enable PID controller 0:0 2 CT N
P2201[3] Fixed PID setpoint 1 0.00 2 CUT N
P2202[3] Fixed PID setpoint 2 10.00 2 CUT N
P2203[3] Fixed PID setpoint 3 20.00 2 CUT N
P2204[3] Fixed PID setpoint 4 30.00 2 CUT N
P2205[3] Fixed PID setpoint 5 40.00 2 CUT N
P2206[3] Fixed PID setpoint 6 50.00 2 CUT N
P2207[3] Fixed PID setpoint 7 60.00 2 CUT N
P2208[3] Fixed PID setpoint 8 70.00 2 CUT N
P2209[3] Fixed PID setpoint 9 80.00 2 CUT N
P2210[3] Fixed PID setpoint 10 90.00 2 CUT N
P2211[3] Fixed PID setpoint 11 100.00 2 CUT N
P2212[3] Fixed PID setpoint 12 110.00 2 CUT N
P2213[3] Fixed PID setpoint 13 120.00 2 CUT N
P2214[3] Fixed PID setpoint 14 130.00 2 CUT N
P2215[3] Fixed PID setpoint 15 130.00 2 CUT N
P2216 Fixed PID setpoint mode - Bit 0 1 3 CT N
P2217 Fixed PID setpoint mode - Bit 1 1 3 CT N
P2218 Fixed PID setpoint mode - Bit 2 1 3 CT N
P2219 Fixed PID setpoint mode - Bit 3 1 3 CT N
r2224 CO: Act. fixed PID setpoint - 2 - -
P2225 Fixed PID setpoint mode - Bit 4 1 3 CT N
P2227 Fixed PID setpoint mode - Bit 5 1 3 CT N
P2231[3] Setpoint memory of PID-MOP 0 2 CUT N
P2232 Inhibit rev. direct. of PID-MOP 1 2 CT N
P2240[3] Setpoint of PID-MOP 10.00 2 CUT N
r2250 CO: Output setpoint of PID-MOP - 2 - -
P2253[3] CI: PID setpoint 0:0 2 CUT N
P2254[3] CI: PID trim source 0:0 3 CUT N
P2255 PID setpoint gain factor 100.00 3 CUT N
P2256 PID trim gain factor 100.00 3 CUT N
P2257 Ramp-up time for PID setpoint 1.00 2 CUT N
P2258 Ramp-down time for PID setpoint 1.00 2 CUT N
r2260 CO: Act. PID setpoint - 2 - -
http://nicontrols.com