Siemens SINUMERIK 802D User Manual

Application Examples
14.1 Cycle example 1
Cylindrical grinding
374 Programming and Operating Manual, 07/2009, 6FC5398-4CP10-2BA0
Table 14- 1 Programming
Program block Explanation
N10 T1 D2 M23
N20 CYCLE420( 160, 0.02, 0.005, 0.005, 0.15, 0.15, 0.15,
0.15, 0.15, 10, 20, 20, 0, , , , 1, 5)
Basic data
N30 CYCLE413( 0, 160.1, 100, -45, 3, ,0.1, 0.03, 0.01,
0.8, 0.3, 0.05, 1, 0, 0, 5)
Right-hand plunge-
cuttiing
N30 T1 D2
N40 CYCLE412( 0, 100, 170, 3, 0.1, 0.1, 0.05, 1, 0.5, 1,
0, 5, 10, 2000)
Right-hand face plunge-
cuttiing
N50 T1 D3
N60 CYCLE411( 0, 160.1, 0, 99, 5, 1, ,0.1, 0.03, 0.01,
0.01, 0.005, 0, 1, 1, 3000, 0.8, 0.8, 0.8, 1, 0, 0, 5)
Multiple plunge-cutting,
only roughing from right
to left
N70 CYCLE415( 0, 160, 0, 99, 3, ,0.15, 0.03, 0.01, 0.02,
0.01, 0.005, -1, 2, 2, 3000, 4000, 5000, 1, 1, 1, 2, 0,
0, 5)
Longitudinal grinding
from right to left
N80 CYCLE410( 0, 180, 99, 3, ,0.1, 0.03, 0.01, 0.8,
0.10, 0.02, 1, 0, 0, 5, 5, 1000)
Oscillating plunge-
cutting
N90 T1 D5
N100 CYCLE412( 0, 130, 176, 3, ,0.1, 0.01, 0.4, 0.1, 1,
0, 5, 10, 1000)
Oscillating face plunge-
cutting
N110 T1 D3
N120 CYCLE410( 0, 170, 136, 3, ,0.1, 0.030, 0.010, 0.8,
0.1, 0.02, 1, 0, 0, 5, ,)
Plunge-cutting
N130 T1 D1
N140 CYCLE413( 0, 160, 160, 45, 3, ,0.1, 0.03, 0.01,
0.8, 0.1, 0.02, 1, 0, 0, 5)
Inclined right-hand
plunge-cuttiing
CN150 YCLE411( 0, 150.1, 165, 260, 5, 1, ,0.1, 0.03,
0.01, 0.01, 0.05, 1, 1, 1, 3000, 1, 1, 1, 0, 0, 0, 5)
Multiple plunge-cutting,
only roughing from left
to right
N160 CYCLE411( 0, 150, 165, 260, 5, 2, ,0.1, 0.03, 0.01,
0.01, 0.005, 1, 1, 1, 3000, 1, 1, 1, 0, 0, 0, 5)
Multiple plunge-cutting,
only finishing/fine
finishing (two-step
longitudinal grinding)
from left to right
N170 M9 M17

Siemens SINUMERIK 802D Specifications

General

Brand	Siemens
Model	SINUMERIK 802D
Category	Control Unit
Language	English