EasyManuals Logo

Siemens SINUMERIK 840D Function Manual

Siemens SINUMERIK 840D
2184 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1999 background imageLoading...
Page #1999 background image
Basic logic functions: NC/PLC interface signals (Z1)
Function Manual, 11/2006, 6FC5397-0BP10-2BA0
3
Table of contents
1 Brief description......................................................................................................................................... 5
2 Detailed Description................................................................................................................................... 7
2.1 Various interface signals and functions (A2) .................................................................................7
2.1.1 Signals from PLC to NC (DB10) ....................................................................................................7
2.1.2 Selection/Status signals from HMI to PLC (DB10) ........................................................................8
2.1.3 Signals from the NC to the PLC (DB10) ........................................................................................9
2.1.4 Signals to Operator Panel (DB19) ...............................................................................................12
2.1.5 Signals from operator control panel (DB19) ................................................................................20
2.1.6 Signals to channel (DB21, ...) ......................................................................................................27
2.1.7 Signals from channel (DB21, ...)..................................................................................................28
2.1.8 Signals to axis/spindle (DB31, ...)................................................................................................29
2.1.9 Signals from axis/spindle (DB31, ...)............................................................................................43
2.2 Axis monitoring, protection zones (A3) ........................................................................................64
2.2.1 Signals to channel (DB21, ...) ......................................................................................................64
2.2.2 Signals from channel (DB21, ...)..................................................................................................65
2.2.3 Signals to axis/spindle (DB31, ...)................................................................................................67
2.2.4 Signals from axis/spindle (DB31, ...)............................................................................................68
2.3 Continuouspath mode, exact stop and LookAhead (B1) .............................................................69
2.3.1 Signals from channel (DB21, ...)..................................................................................................69
2.3.2 Signals from axis/spindle (DB31, ...)............................................................................................69
2.4 Acceleration (B2) .........................................................................................................................70
2.5 Diagnostic tools (D1)....................................................................................................................70
2.6 Travel to fixed stop (F1) ...............................................................................................................71
2.6.1 Signals to axis/spindle (DB31, ...)................................................................................................71
2.6.2 Signals from axis/spindle (DB31, ...)............................................................................................73
2.7 Velocities, Setpoint/Actual Value Systems, Closed-Loop Control (G2).......................................73
2.8 Help function output to PLC (H2).................................................................................................74
2.8.1 Signals to channel (DB21, ...) ......................................................................................................74
2.8.2 Signals from channel (DB21, ...)..................................................................................................74
2.8.3 Signals from axis/spindle (DB31, ...)............................................................................................78
2.9 Mode group, channel, program operation, reset response (K1)..................................................79
2.9.1 Signals to mode group (DB11).....................................................................................................79
2.9.2 Signals from the mode group (DB11) ..........................................................................................83
2.9.3 Signals to channel (DB21, ...) ......................................................................................................87
2.9.4 Signals from channel (DB21, ...)..................................................................................................93
2.9.5 Signals to axis/spindle (DB31, ...)..............................................................................................106
2.9.6 Signals from axis/spindle (DB31, ...)..........................................................................................106
2.10 Axis types, coordinate systems, frames (K2).............................................................................108
2.10.1 Signals to axis/spindle (DB31, ...)..............................................................................................108

Table of Contents

Other manuals for Siemens SINUMERIK 840D

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Siemens SINUMERIK 840D and is the answer not in the manual?

Siemens SINUMERIK 840D Specifications

General IconGeneral
SeriesSINUMERIK 840D
AxesUp to 31
ChannelsUp to 10
Operating SystemWindows-based
Power Supply24 V DC
Control Unit TypeCNC
InterfaceEthernet, PROFIBUS
DisplayTFT color display
InterpolationSpline
PLCIntegrated PLC
Data StorageCompactFlash, USB

Related product manuals