EasyManuals Logo

Siemens SINUMERIK 840D Function Manual

Siemens SINUMERIK 840D
2184 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #561 background imageLoading...
Page #561 background image
Basic logic functions: Mode group, channel, program operation, reset response (K1)
Function Manual, 11/2006, 6FC5397-0BP10-2BA0
3
Table of contents
1 Brief description......................................................................................................................................... 7
2 Detailed description ................................................................................................................................. 11
2.1 Mode group..................................................................................................................................11
2.1.1 Mode group Stop .........................................................................................................................15
2.1.2 Mode group RESET.....................................................................................................................15
2.2 Mode groups ................................................................................................................................16
2.2.1 Monitoring functions and interlocks of the individual modes .......................................................22
2.2.2 Mode change ...............................................................................................................................23
2.3 Channel........................................................................................................................................24
2.3.1 Global start disable for channel ...................................................................................................28
2.4 Program test.................................................................................................................................29
2.4.1 Program execution without setpoint outputs................................................................................29
2.4.2 Program execution in singleblock mode ......................................................................................31
2.4.3 Program execution with dry run feedrate.....................................................................................34
2.4.4 Skip part-program blocks .............................................................................................................35
2.5 Block search.................................................................................................................................37
2.5.1 Sequence for block search of Type 1, 2 and 4 ............................................................................38
2.5.2 Block search in connection with other NCK functions .................................................................40
2.5.2.1 ASUB after and during block search............................................................................................40
2.5.2.2 PLC actions after block search ....................................................................................................41
2.5.2.3 Spindle functions after block search ............................................................................................42
2.5.3 Automatic start of an ASUB after block search............................................................................43
2.5.4 Cascaded block search................................................................................................................44
2.5.5 Examples of block search with calculation ..................................................................................46
2.6 Block search Type 5 SERUPRO..................................................................................................50
2.6.1 REPOS.........................................................................................................................................58
2.6.1.1 Continue machining after SERUPRO search target found..........................................................58
2.6.1.2 Repositioning on contour with controlled REPOS .......................................................................69
2.6.2 Acceleration measures via MD ....................................................................................................72
2.6.3 SERUPRO ASUP ........................................................................................................................73
2.6.4 Selfacting SERUPRO ..................................................................................................................76
2.6.5 Inhibit specific part of the program in the part program for SERUPRO.......................................78
2.6.6 Special features in the part-program target block........................................................................82
2.6.6.1 STOPRE in the part-program target block...................................................................................82
2.6.6.2 SPOS in target block....................................................................................................................83
2.6.7 Behavior during POWER ON, mode change and RESET...........................................................83
2.6.8 Special features of functions supported during SERUPRO.........................................................84
2.6.8.1 Travel to fixed stop (FXS) ............................................................................................................84
2.6.8.2 Force Control (FOC) ....................................................................................................................85
2.6.8.3 Synchronous spindle....................................................................................................................85
2.6.8.4 Couplings and master-slave ........................................................................................................86
2.6.8.5 Axis functions...............................................................................................................................89
2.6.8.6 Gear stage change ......................................................................................................................91
2.6.8.7 Superimposed motion..................................................................................................................91

Table of Contents

Other manuals for Siemens SINUMERIK 840D

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Siemens SINUMERIK 840D and is the answer not in the manual?

Siemens SINUMERIK 840D Specifications

General IconGeneral
SeriesSINUMERIK 840D
AxesUp to 31
ChannelsUp to 10
Operating SystemWindows-based
Power Supply24 V DC
Control Unit TypeCNC
InterfaceEthernet, PROFIBUS
DisplayTFT color display
InterpolationSpline
PLCIntegrated PLC
Data StorageCompactFlash, USB

Related product manuals