Sony DSC-S70 - Strobe White Balance Adjustment; Strobe Light Level and White Balance Check

5-23
14. Strobe Light Level and White balance Check
Check the light level regulation and the white balance when the
strobe light flashed.
Mode STILL
Subject Flash adjustment box (Note 3)
(1.0 m from the front of lens)
Measurement Point Displayed data of page: 1
Measuring Instrument Adjusting remote commander
Specified value Y level data: 60 to 94
R-Y level data: FA to FF or 00 to 06
(Note 4)
B-Y level data: FA to FF or 00 to 06
(Note 4)
Note 1: Perform this checking successively after performing
“Flange Back Adjustment”, “ Light Level Adjustment”, “Strobe
White Balance Adjustment” and “Auto White Balance Standard
Data Input”. (Do not turn the power of unit OFF)
Note 2: Perform this adjustment in the Flash adjustment box.
Note 3: Refer to “4. Preparing the Fiash adjustment box”.
(See page 5-7)
Note 4: The right four digits of the page: 1 displayed data of the
adjusting remote commander.
1:XX:XX
 B-Y level data
 R-Y level data
Note 5: Displayed data of page: F, address: 64 of theadjusting
remote commander.
F:XX:64
 Y level data
Note 6: Check that the data of page: 6, address: 02 is “00”.
Checking method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 6, address: 01, set data: 79, and press the PAUSE
button of the adjusting remote commander.
3) Select page: 6, address: 01, set data: 67, and press the PAUSE
button.
4) Check the flashing of strobe light.
5) Select page: F, address: 64, and check that the data satisfies
the Y level data specified value. (Note 5)
6) Select page: 0, address: 03, and set data: 02.
7) Select page: 1, and check the R-Y, B-Y level data (Note 4)
satisfies the specified value.
Processing after Completing Adjustments:
1) Select page: 0, address: 03, and set data: 00.
2) Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjusting remote commander.
3) Select page: 6, address: 2C, and set data: 00.
4) Select page: 6, address: 6C, and set data: 00.
5) Select page: 6, address: 93, and set data: 00.
6) Select page: 7, address: 03, set data: 00, and press the PAUSE
button.
7) Select page: 5, address: F1, and set data: 00.
8) Select page: D, address: 63, set data: 00, and press the PAUSE
button.
9) Release the data setting performed at step 4) of “Strobe White
Balance Adjustment”. (Refer to page 5-13)
10) Select page: 0, address: 01, and set data: 00.
13. Strobe White Balance Adjustment
Adjust the white balance when the strobe light flashed.
Mode STILL
Subject Flash adjustment box (Note 3)
(1.0 m from the front of lens)
Adjustment Page F
Adjustment Address 4D, 4E, 64, 69, 6A, 6B
Note 1: Perform “Flange Back Adjustment”, “Light Level
Adjustment”, “Auto White Balance Adjustment” and
“Auto White Balance Standard Data Input” before this
adjustment.
Note 2: Perform this adjustment in the Flash adjustment box.
Note 3: Refer to “4. Preparing the Flash adjustment box”.
(See page 5-7)
Note 4: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Switch setting:
1) FLASH ...................... ON
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 5, address: F1, and set data: FF.
3) Select page: D, address: 63, set data: 40, and press the PAUSE
button of the adjusting remote commander.
4) Perform “ Data setting during camera system adjustment”.
(Refer to page 5-13)
5) Select page: 7, address: 03, and set data: 08.
6) Select page: 6, address: 90, and set data: 00.
7) Select page: 6, address: 91, and set data: 00.
8) Select page: 6, address: 92, and set data: 00.
9) Select page: 6, address: 93, and set data: 80.
10) Select page: 6, address: 6C, and set data: 01.
11) Select page: 6, address: 2C, and set data: 01.
12) Select page: 6, address: 01, set data: 79, and press the PAUSE
button.
13) Select page: 6, address: 01, set data: 67, and press the PAUSE
button.
14) Select page: 6, address: 01, set data: 00, and press the PAUSE
button.
15) Select page: 6, address: 01, set data: 79, and press the PAUSE
button.
16) Select page: 6, address: 01, set data: 67, and press the PAUSE
button.
17) Select page: 6, address: 01, set data: 00, and press the PAUSE
button.
18) Select page: 6, address: 01, set data: 79, and press the PAUSE
button.
19) Select page: 6, address: 01, set data: B9, and press the PAUSE
button. (The strobe white balance adjustment is performed
and the adjustment data is stored in page: F, address: 4D, 4E,
64, 69, 6A and 6B)
20) Select page: 6, address: 02, and check that the data is “01”.
Processing after Completing Adjustments:
1) Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjusting remote commander.
2) Perform “Strobe Light Level and White Balance Check” suc-
cessively. (Do not turn the power of unit OFF)