Stryker Power-LOAD 6390 User Manual

EEMMCC iinnffoorrmmaattiioonn
GGuuiiddaannccee aanndd mmaannuuffaaccttuurreerr’’ss ddeeccllaarraattiioonn -- eelleeccttrroommaaggnneettiicc eemmiissssiioonnss
PPoowweerr--LLOOAADD is intended for use in the electromagnetic environment specified below. The customer or the user of
PPoowweerr--LLOOAADD should assure that it is used in such an environment.
EEmmiissssiioonnss tteesstt
CCoommpplliiaannccee EElleeccttrroommaaggnneettiicc eennvviirroonnmmeenntt
RF Emissions
CISPR 11
Group 1
The PPoowweerr--LLOOAADD system uses RF energy
only for its internal function. Therefore, its RF
emissions are very low and are not likely to
cause any interference in nearby electronic
equipment.
RF Emissions
CISPR 11
Group 2
The PPoowweerr--LLOOAADD system must emit
electromagnetic energy in order to perform its
intended function. Nearby electronic
equipment may be affected.
RF Emissions
CISPR 11
Class A
The PPoowweerr--LLOOAADD system is suitable for use
in all establishments other than domestic and
those directly connected to the public low-
voltage power supply network that supplies
buildings used for domestic purposes.
RReeccoommmmeennddeedd sseeppaarraattiioonnss ddiissttaanncceess bbeettwweeeenn ppoorrttaabbllee aanndd mmoobbiillee RRFF ccoommmmuunniiccaattiioonnss eeqquuiippmmeenntt aanndd PPoowweerr--
LLOOAADD
PPoowweerr--LLOOAADD is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
The customer or the user of PPoowweerr--LLOOAADD can help prevent electromagnetic interferences by maintaining a minimum
distance between portable and mobile RF communications equipment (transmitters) and PPoowweerr--LLOOAADD as
recommended below, according to the maximum output power of the communications equipment.
RRaatteedd mmaaxxiimmuumm oouuttppuutt
ppoowweerr ooff ttrraannssmmiitttteerr
WW
SSeeppaarraattiioonn ddiissttaannccee aaccccoorrddiinngg ttoo ffrreeqquueennccyy ooff ttrraannssmmiitttteerr
mm
115500 kkHHzz ttoo 8800 MMHHzz
dd==((11..22)) ((√√PP))
8800 MMHHzz ttoo 880000 MMHHzz
dd==((00..3355)) ((√√PP))
880000 MMHHzz ttoo 22..77 GGHHzz
dd==((00..7700)) ((√√PP))
0.01 0.12 0.04 0.07
0.1 0.38 0.11 0.22
1 1.20 0.35 0.70
10 3.79 1.11 2.21
100 12 3.5 7
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters
(m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output
power rating of the transmitter in watts (W) according to the transmitter manufacturer. Note 1: At 80 MHz and 800 MHz,
the separation distance for the higher frequency range applies. Note 2: These guidelines may not apply in all situations.
Electromagnetic propagation is affected by absorption and reflection from structures, objects, and people.
6390-709-001 Rev AB.1 55 EN

Stryker Power-LOAD 6390 Specifications

General

Brand	Stryker
Model	Power-LOAD 6390
Category	Medical Equipment
Language	English