TDK-Lambda GENESYS 10KW - Chapter 2: Specifications; EMC Compliance

83
-
530
-
000 Rev.
G
13
1. 208 Volts Input Models
1. ESD
---
2. Fast transients
---
3. Surge immunity
---
4. Conducted immunity
---
5. Radiated immunity
---
6. Power Frequency Magnetic Field
7. Conducted emission
---
8. Radiated emission
---
2. 400 Volts Input Models
CE Mark
1. ESD
---
2. Fast transients
---
3. Surge immunity
---
4. Conducted immunity
---
5. Radiated immunity
---
6. Power Frequency Magnetic Field
---
7. Voltage Dips, Short Interruptions and
---
Voltage Variations Immunity Tests
(400VAC Input Only)
8. Conducted emission
---
9. Radiated emission
---
CE Mark
EN55011A, FCC part 15J-A
EN61000-4-5 (IEC 1000-4-5)
EN61000-4-8
IEC 61000-4-11
EN61000-4-8
EN61000-4-6 (IEC 1000-4-6)
EN61000-4-2 (IEC 801-2) Air-disch.+/-8kV , contact disch.+/-4kV
EN61000-4-4 (IEC 1000-4-3)
EN61000-4-3 (IEC 1000-4-3)
EN55011A, FCC part 15J-A
EN61000-4-2 (IEC 801-2) Air-disch.+/-8kV , contact disch.+/-4kV
EN55011A, FCC part 15J-A
12. EMC
EN61000-4-4 (IEC 1000-4-3)
EN55011A, FCC part 15J-A
EN61000-4-5 (IEC 1000-4-5)
EN61000-4-6 (IEC 1000-4-6)
EN61000-4-3 (IEC 1000-4-3)
13. RELIABILITY SPECS
1. Electrolytic capacitors life
Yrs.
More than 3yrs at 40C ambient , 100% load
2. Grade
---
4. W arranty
Yrs.
5 years
5. Shelf life
Yrs.
1. applicable standards
---
2. Insulation resistance
---
100Mohm at 500Vdc
J1-1
ENA_IN
Enable/Disable Dry Contact with J1-14
J1-2
IF_CO M
Isolated Interface Common. Return for SO, PS_OK
J1-3
IF_CO M
Isolated Interface Common. Return for SO, PS_OK
J1-4
N/C
J1-5
N/C
J1-6
N/C
J1-7
N/C
J1-8
LOC/REM
Input for selecting between Local or Remote analog programming
J1-9
VPG M
Input for remote analog voltage/resistance program ming of the O utput Voltage
J1-10
IPGM
Input for remote analog voltage/resistance program ming of the O utput Current
J1-11
VM ON
Output Voltage Monitor
J1-12
CO M
Control Co mmon for VMON & IMON
J1-13
CV/CC
Output for Constant Voltage/ Constant Current mode indication
J1-14
ENA_OUT
Enable/Disable Dry Contact with J1-1
J1-15
SO
Input for Shut-Off control of the output.
J1-16
PS_ OK
Output for indication of the power supply status
J1-17
N/C
J1-18
N/C
J1-19
N/C
J1-20
N/C
J1-21
LOC/REM Signal
Output for indicating if the unit is in Local or Remote analog programming mode.
J1-22
VPG M_RTN
Return for VPGM J1-9; connected to Neg Output
J1-23
IPGM _RTN
Return for IPGM J1-10; connected to Neg O utput
J1-24
IMON
Output for Current Monitor
J1-25
P
Output for Current Balance in Parallel Operation (O ne wire - Re ference to Negative Output)
14. SAFETY
G-2 , Lambda Group derating criteria & EIAJ RCR-9102A
15. J1 Connector
count Reliabililty, Generic FaIlure rates, 25C
UL/ULC 60950-1, EN60950-1 recognized. All O utputs are Hazardous. (Units with IEMD or ISOL option are Recognized up
to 400 volts output). CE Mark 208 & 40 0VAC input only (CB Scheme).
5 years , electrolytic caps shall be reformed after 2 years