TDK-Lambda GENESYS 10KW - Table of Contents

83
-
530
-
000 Rev
G
4
WARRANTY
................................
................................
................................
..............................
1
CHAPTER 1 GENERAL IN
FORMATION
................................
................................
...................
6
1.1 USER MANUAL CONTENT
................................
................................
................................
...................
6
1.2 INTRODUCTION
................................
................................
................................
................................
.....
6
1.3 ACCESSORIES
................................
................................
................................
................................
......
8
1.4 MODEL NUMBER FORMAT
................................
................................
................................
...................
9
CHAPTER 2 SPECIFIC
ATIONS
................................
................................
.............................
10
CHAPTER 3 INSTALL
ATION
................................
................................
................................
14
3.1 GENERAL
14
3.2 PREPARATION FOR USE
................................
................................
................................
....................
14
3.3 INITIAL INSPECTIONS
................................
................................
................................
.........................
14
3.4 RACK MOUNTING
................................
................................
................................
...............................
14
3.5 LOCATON, MOUNTING AND COOLING
................................
................................
.............................
15
3.6 AC SOURCE REQUIREMENTS
................................
................................
................................
...........
15
3.7 AC INPUT POWER CONNECTION
................................
................................
................................
......
15
3.8 TURN
-
ON CHECKOUT PROCEDURE
................................
................................
................................
.
17
3.9
CONNECTING THE LOAD
................................
................................
................................
............
19
3.10 LOCAL AND REMOTE SENSING
................................
................................
................................
.......
22
CHAPTER 4 FRONT AN
D REAR PANEL CONTROL
S AND CONNECTORS
.......................
25
4.1 INTRODUCTION
................................
................................
................................
................................
...
25
4.2 FRONT PANEL CONTROLS AND INDICATORS
................................
................................
................
25
4.3 REAR PANEL CONTROLS AND INDICATORS
................................
................................
...................
29
4.4
REAR PANEL SW1 SETUP SWITCH
................................
................................
................................
..
29
4.5 REAR PANEL J1 PROGRAMMING AND MONITORING CONNECTOR
................................
.............
31
CHAPTER 5 LOCAL OPER
ATION
................................
................................
...........................
33
5.1 INTRODUCTION
................................
................................
................................
................................
...
33
5.2 STANDARD OPERATION
................................
................................
................................
.....................
33
5.3 OVER VOLTAGE PROTECTION (OVP)
................................
................................
...............................
34
5.4 UNDER VOLTAGE LIMIT (UVL)
................................
................................
................................
...........
35
5.5 FOLDBACK PROTECTION
................................
................................
................................
...................
35
5.6 OUTPUT ON/OFF CONTROL
................................
................................
................................
..............
35
5.7 OUTPUT SHUT
-
OFF (SO) CONTROL VIA REAR PANEL J1 CONNECTOR
................................
.....
35
5.8 ENABLE/DISABLE CONTROL VIA REAR PANEL J1 CONNECTOR
................................
.................
36
5.9 CV/CC SIGNAL
................................
................................
................................
................................
.....
36
5.10 PS_OK SIGNAL
................................
................................
................................
................................
...
36
5.11 SAFE START AND AUTO
-
RESTART MODES
................................
................................
..................
37
5.12 OVER TEMPERATURE PROTECTON (OTP)
................................
................................
....................
37
5.13 LAST SETTING MEMORY
................................
................................
................................
..................
37
5.14 SERIES OPERATION
................................
................................
................................
.........................
37
5.15 PARALLEL OPERATION
................................
................................
................................
....................
40
5.16 DAISY
-
CHAIN CONNECTION
................................
................................
................................
............
41
5.17 ADVANCED PARALLEL OPERATION
................................
................................
...............................
41
5.18 FRONT PANEL LOCKING
................................
................................
................................
..................
44
CHAPTER 6 REMOTE AN
ALOG PROGRAMMING
................................
................................
45
6.1 INTRODUCTION
................................
................................
................................
................................
...
45
6.2 LOCAL/REM
OTE ANALOG INDICATION
................................
................................
............................
45
6.3 LOCAL/REMOTE ANALOG INDICATION
................................
................................
............................
45
6.4 REMOTE VOLTAGE PROGRAMMING OF OUTPUT VOLTAGE AND CURRENT LIMI
T
..................
46
6.5 RESISTIVE PROGRAMMING OF OUTPUT VOLTAGE AND CURRENT LIMIT
................................
.
47
6.6 REMOTE MONITORING OF OUTPUT VOLTAGE AND CURRENT
................................
..................
48