What to do if my TechniSat Receiver has no image, no sound, and the display doesn't illuminate?
If your TechniSat Receiver displays no image, sound, and the display doesn't illuminate, the issue might be due to a lack of mains voltage. Check both the mains power outlet and the plug to ensure they are functioning correctly.
What to do if my TechniSat Receiver has no image, no sound, but the display illuminates?
If your TechniSat Receiver shows no image or sound but the display illuminates, there could be several reasons: * A short-circuit in the LNB connection. In this case, switch off the device, rectify the short-circuit, and then switch the device back on. * A defective or missing cable connection. Check all cable settings. * A faulty LNB. Consider replacing the LNB. * An incorrect outdoor unit setting on the receiver. Modify the setting accordingly.
Why am I getting no reception for channels which were OK before on my TechniSat Receiver?
If you're experiencing a loss of channels on your TechniSat Receiver that were previously working, the issue could stem from several causes: * The dish might be incorrectly positioned or faulty. Check the dish's alignment and condition. * The channel might now be transmitted on a different transponder. Perform a channel search or scan to update your channel list. * The channel might no longer be transmitted.
How to fix a TechniSat Receiver remote control that does not work?
If your TechniSat Receiver's remote control isn't working, it could be due to an incorrect remote control code being set. In this case, set the correct remote control code. Alternatively, the batteries might be spent, so try replacing them.
Why does the picture on my TechniSat Receiver sometimes have square blocks?
If your TechniSat Receiver picture sometimes has square blocks, it may be caused by: * Heavy rain or snow. Remove snow from the dish. * Dish incorrectly aligned. Re-align dish. * Dish is too small at the reception location. Use larger dish. * There is an obstacle between the dish and the satellite (e.g. a tree). Mount the dish in an unobstructed position.
What to do if I have sound but no TV picture on my TechniSat Receiver?
If you're getting sound but no TV picture on your TechniSat Receiver, it's possible that radio mode is selected and the radio background image is switched off. Check the settings to resolve this.
Why am I getting no picture via HDMI on my TechniSat Receiver?
If you're not getting a picture via HDMI on your TechniSat Receiver, it might be due to an incorrect HDMI sound format being selected. Check the HDMI sound format settings to ensure they are correctly configured.
What to do if the picture on my TechniSat Receiver is incomplete or distorted?
If you're experiencing incomplete or distorted picture on your TechniSat Receiver, it could be due to an incorrect picture format being set. Check the picture format settings. It may also be caused by an incorrect picture display or zoom selection. Check the picture display/zoom in the menu and zoom settings.
Why is there no sound or incorrect sound on my TechniSat Receiver?
If you're getting no sound or incorrect sound from your TechniSat Receiver, it could be because Dolby Digital is active or an incorrect audio language is selected. Check the settings in the menu and also check Dolby Digital / language selection.
What to do if my TechniSat Receiver has no connection to the network?
If your TechniSat Receiver has no connection to the network, it may be caused by: * Incorrect network settings. Check the network settings. * Network cable not connected correctly. Check the network connection. * Network connection not allowed. Allow network connection in Special functions > Allow network.
General| Signal source | Ethernet (RJ-45), Satellite |
|---|---|
| Supported video modes | 576i, 576p, 720p, 1080i, 1080p |
| Digital signal format system | DVB-S, DVB-S2 |
| Personal Video Recorder (PVR) included | - |
| Tuner type | Digital |
| Product color | Black |
| Number of tuners | 1 tuner(s) |
| Audio output channels | - channels |
| On Screen Display (OSD) | Yes |
| Audio formats supported | AAC, AC3, AIFF, FLAC, MP2, MP3, OGG, WAV |
| Image formats supported | BMP, GIF, JPEG, PNG, TIFF |
| Video formats supported | ASF, AVI, M2TS, M4V, MKV, MOV, MP4, MPG, TS, TS4, XVID |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Ethernet LAN data rates | 10, 100 Mbit/s |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Power consumption (standby) | 0.3 W |
| Power consumption (typical) | 4.8 W |
| Package weight | 1240 g |
Weight and Dimensions| Depth | 177 mm |
|---|---|
| Width | 220 mm |
| Height | 45 mm |
| Weight | 600 g |
Identifies and describes the front panel controls and indicators.
Details the ports and connectors on the rear of the receiver and front flap slots.
Covers crucial introductory content, intended use, and safety guidelines.
Provides critical safety guidelines for operating the device.
Provides advice on breaks, operation notes, data security, and battery replacement.
Guides on environmentally responsible disposal of the device and packaging.
Lists optional accessories like remote controls, adapters, and dongles.
Details how to connect the receiver to the main power supply.
Covers connecting satellite, TV (HDMI/analog), Hi-Fi/Surround, and USB accessories.
Explains network port, analogue AV, and basic operation overview with OSD.
Covers switching the device on/off and navigating the main menu.
Details navigating settings menus, accepting, and exiting changes.
Explains how to save or discard menu changes and exit menus.
Outlines methods like arrow selection, selection lists, number entry, and virtual keyboard.
Describes using arrow buttons to alter values with side indicators.
Explains using selection lists for changing settings like OSD font size.
Covers number entry and virtual keyboard usage for setting changes.
Details using the numeric keypad for SMS-style text input.
Describes how to access and use option menus for various functions.
Introduces the automatic installation wizard and its initial steps.
Guides on selecting the operating language and country for the receiver.
Explains enabling internet connection and agreeing to data protection terms.
Covers setting the picture format and configuring the antenna setup.
Guides on checking and modifying network settings for LAN or WLAN.
Details the software update process and channel scanning procedures.
Covers selecting regional channels and managing channel lists.
Explains the process of downloading SFI data for the Electronic Programme Guide (EPG).
Covers switching the device on/off and initial channel selection methods.
Details using number buttons, the channel navigator, and list selection.
Covers selecting lists, filtering, switching TV/Radio modes, and info box.
Covers filtering channel lists and retrieving blocked channels via PIN.
Covers returning to last channel, TV/Radio switching, regional channels, and info box.
Explains using smart cards and CI/CI+ modules for encrypted content.
Covers adjusting volume, muting, and selecting sound/language options.
Details freeze frame, Teletext, and subtitle display functionalities.
Explains the components and navigation of the SFI (Electronic Programme Guide) display.
Lists and describes various timer functions like DVR, channel switching, and alarm timers.
Guides on accessing the navigation menu to select different operational modes.
Describes options for inserted storage volumes like playing media or setting as recording volume.
Introduces DVR recording and its different modes like instant, timer, and timeshift.
Covers manually and automatically ending DVR recordings, saving or discarding them.
Details DVR timer setup and starting the timeshift function for live playback during recording.
Explains accessing DVR playback, controls like pause/ff/rewind, tags, and stopping playback.
Covers CAM-MHEG Autostart, PIN input, and manual CI/CI+ module initialization.
Details how to activate the simplified ISI mode and its core features.
Covers channel selection, TV/Radio switching, and volume/mute controls in ISI mode.
Details Teletext operations like page selection and exiting within ISI mode.
Provides step-by-step instructions for updating receiver software using a USB stick.
Addresses common issues like remote control, picture/sound problems, signal, network, and DVR faults.
Solves problems related to device power, reset, USB detection, and standby functions.
Outlines warranty period, manufacturer details, and legal compliance information.
Mentions EU declarations, HDMI, and Dolby licensing and trademarks.
To Next Page
