Telephone Button Programming
300 Series Programs
13-62 Strata CTX Programming - Part 3: Telephone Button Programming 11/03
310-
01~03
Day1/Day2/Night
Destination Type
)%
~
)%
, n,
6SNU
n = 1. No Data (default)
2. Dialing Digits
3. DISA
4. Built-in Modem
5. Night Bell
Select Destination Type for each.
• No Data – no destination will ring when the line rings into the
system.
• Dialing Digits – assigns the line to ring the directory number or
access code defined in the “Destination Digits” assignment
• DISA – assigns the line to ring in as a DISA call. DISA dial tone
will be returned to the caller.
• Modem – assigns the line to ring the remote maintenance modem
on the CTX processor. Used to call into the system with a CTX
WinAdmin PC and modem.
• Night Bell – Assigns the line to cause the night relay to pulse
(one-sec. close/3-sec. open)
Day1/Day2/Night
Destination Digits
n1,
+ROG
n1 = Up to 32 digits Enter Destination, Directory Number or Access Codes for each, only
if Dialing Digits is selected as Destination Type.
• If Dialing Digits is the Destination Type, enter the Directory
Number that the line should ring.If the line should ring over
external page, enter #31xx, where xx is the external Page group
number.
• If the default page access code #31 was changed, use the new
page access code as the leading digits.
• Line access codes and network routing numbers can also be
entered to route incoming calls back out to a public or private
network number.
310-04 MOH Source
)%
, n,
+ROG
,
+ROG
n = 1. Silence
2. External 1 (default)
3. External 2
4. External 3
5. External 4
6. External 5
7. External 6
8. External 7
9. External 8
10. External 9
11. External 10
12. External 11
13. External 12
14. External 13
15. External 14
16. External 15
Select the MOH source for Analog DIT Trunk. The Scroll key must be
used to select MOH sources indicated by 10 or higher.
311
DISA Security Codes
,
+ROG
This command assigns DISA parameters.
311-01 DISA Enabled
)%
, n,
+ROG
n = 1. Enable
2. Disable (default)
Enable DISA security code.
311-02 DISA Code
)%
, n,
+ROG
n = Up to 15 digits Enter DISA security code.
311-03 Response Timer
)%
, n,
+ROG
n = 0~30
(default = 5)
Enter the time, in seconds, for Strata CTX to respond to a call.
311-04 Idle Timer
)%
, n,
+ROG+ROG
n = 0~60
(default = 10)
Enter the time in seconds to wait for idle DTMF.
311-05 Tie Line Access
)%
, n,
+ROG+ROG
n = 1. Enable
2. Disable (default)
Enable this feature to allow DISA callers to access Tie lines when
they call into the system.
313
Caller ID Assignment
,
+ROG
This program assigns Caller ID circuits to the CO Line to which the
circuit is connected. The ANI, DNIS, DID formats for TI and analog
DID CO Lines are also defined.
313-00 Trunk Number
n,
+ROG
,
n = 1~64 (CTX100)
1~96 (CTX670 Basic)
1~264 (CTX670 Exp.)
Enter the Trunk Number.
Table 13-28 Programs 303~315 (continued)
Button Sequence Value(s) Summary
To Next Page
Loading...
