E6581595
L-1
12
12. Specifications
12.1 Models and their standard specifications
Standard specifications
Item Specification
Input voltage class 3-phase 240V class
Applicable motor (kW) 0.1 0.2 0.4 0.75 1.5 2.2 4.0
Rating
Type VFNC3
Form 2001P 2002P 2004P 2007P 2015P 2022P 2037P
Capacity (kVA) Note 1) 0.3 0.6 1.0 1.6 2.9 3.9 6.4
Output current
(A) Note 2)
0.7
(0.7)
1.4
(1.4)
2.4
(2.4)
4.2
(3.6)
7.5
(7.5)
10.0
(8.5)
16.7
(14.0)
Output voltage Note 3) 3-phase 200V to 240V
Overload current rating
150％-60 seconds, 200%-0.5 second
Power supply
Voltage-frequency 3-phase 200V to 240V - 50/60Hz
Allowable fluctuation Voltage 170 to 264V Note 4), frequency ±5%
Required Power supply
capacity (kVA) Note 5)
0.5 0.8 1.4 2.5 4.3 5.7 9.2
Protective method (IEC60529) IP20
Cooling method Self-cooling Forced air-cooled
Color RAL 3002 / 7016
Built-in filter -
Item Specification
Input voltage class 1-phase 240V class 1-phase 120V class
Applicable motor (kW) 0.1 0.2 0.4 0.75 1.5 2.2 0.1 0.2 0.4 0.75
Rating
Type VFNC3S
Form 2001PL 2002PL 2004PL 2007PL 2015PL 2022PL 1001P 1002P 1004P 1007P
Capacity (kVA) Note 1) 0.3 0.6 1.0 1.6 2.9 3.9 0.3 0.6 1.0 1.6
Output current
(A) Note 2)
0.7
(0.7)
1.4
(1.4)
2.4
(2.4)
4.2
(3.2)
7.5
(7.5)
10.0
(9.1)
0.7
(0.7)
1.4
(1.4)
2.4
(2.4)
4.2
(4.0)
Rated output voltage Note 3) 3-phase 200V to 240V 3-phase 200V to 240V
Overload current rating
150％-60 seconds, 200% -0.5 second 150％-60 seconds, 200%-0.5 second
Power supply
Voltage-frequency 1-phase 200V to 240V - 50/60Hz 1-phase 100V to 120V – 50/60Hz
Allowable fluctuation Voltage 170 to 264V Note 4), frequency ±5%
Voltage 85 to 132V Note 4), frequency±5％
Required Power supply
capacity (kVA) Note 5)
0.5 0.8 1.3 2.3 4.0 5.4 0.4 0.7 1.3 2.1
Protective method (IEC60529) IP20 IP20
Cooling method Self-cooling Forced air-cooled Self-cooling
Forced air-
cooled
Color RAL 3002 / 7016 RAL 3002 / 7016
Built-in filter EMC filter -
Note 1. Capacity is calculated at 220V for output voltage.
Note 2. Indicates rated output current setting when the PWM carrier frequency (parameter f300) is 4kHz or less. Between 5
kHz and 12 kHz, the rated output current is indicated in the ( ). Above 13 kHz, the output current must be reduced. The
default setting of the PWM carrier frequency is 12kHz. (Refer to section 6.11)
Note 3. Maximum output voltage is the same as the input voltage. In case of 1-phase 120V class, maximum output voltage is
same as twice the input voltage.
With regard to 120V models, the output voltage may decrease about 10 to 20 % if motor load is applied. When
operating VFNC3 in conjunction with general-purpose motor (200V), it is necessary to reduce the motor load.
Note 4. 180V-264V (240V class), 90V-132V (120V class) when the inverter is used continuously (load of 100%).
Note 5. Required power supply capacity varies with the value of the power supply side inverter impedance (including those of
the input reactor and cables).
To Next Page
Loading...
Need help?
General
