Need help?Do you have a question about the TP-Link TL-R600VPN and is the answer not in the manual?
General| VPN Support | Yes |
|---|---|
| Firewall | SPI Firewall |
| Network Standards | IEEE 802.3, 802.3u, 802.3ab |
| Button | Reset button |
| Flash | 8MB |
| DRAM | 64MB |
| Device Type | VPN Router |
| WAN Ports | 1 x 10/100/1000Mbps |
| LAN Ports | 4 |
| Management | Web-based GUI, SNMP v1/2c |
| Standards and Protocols | TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP |
| Network Media | 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m), EIA/TIA-568 100Ω STP (maximum 100m) |
| DHCP | DHCP Server, DHCP Client |
| Dynamic DNS | DynDns, NO-IP |
| Security | DoS, SPI Firewall, IP Address Filter/MAC Address Filter/Domain Filter, IP and MAC Address Binding |
Displays the router's hardware, firmware, system time, and interface status.
Provides detailed data on network traffic for interfaces and IP addresses.
Displays detailed traffic data for each network interface.
Shows traffic statistics for specific IP addresses or ranges.
Configures the router's WAN connections and port settings.
Sets the number of active WAN ports for internet connectivity.
Configures various connection types (Static IP, PPPoE, etc.) for WAN ports.
Manages the router's Local Area Network settings.
Sets the IP address and subnet mask for the router's LAN interface.
Configures the DHCP server to automatically assign IP addresses to LAN clients.
Configures IPTV service settings based on ISP requirements.
Manages MAC addresses for WAN and LAN ports.
Manages switch port settings and monitoring.
Manages Virtual LANs for network segmentation.
Configures IPv6 network settings.
Configures IPv6 address assignment methods (DHCPv6, SLAAC) for the LAN clients.
Configures IPv6 WAN connections, including port selection and connection types.
Configures IPv6 WAN connection types like Static IP, PPPoE, and 6to4 Tunnel.
Sets up dynamic IPv6 addressing using SLAAC or DHCPv6.
Configures static IPv6 addressing parameters provided by the ISP.
Configures PPPoE connection for IPv6, including advanced settings.
Manages IP address groups for use in various network rules.
Defines specific time periods for rules to be effective.
Creates IP address pools for VPN clients, specifying name and IP range.
Configures Network Address Translation settings.
Sets up NAT for multiple subnets to allow simultaneous internet access.
Creates a direct IP mapping between private and public IP addresses.
Configures virtual servers to make local services accessible from the internet.
Manages bandwidth usage by setting rules for data flows.
Enables and configures bandwidth control rules to manage data flow limits.
Limits the number of concurrent network sessions.
Optimizes WAN link usage through load balancing.
Enables and configures load balancing methods to optimize WAN link usage.
Sets up a backup WAN link to ensure continuous network availability.
Manages static and policy-based routing.
Explains the firewall's role in network security.
Configures various firewall features.
Protects the network from ARP spoofing attacks using IP-MAC binding.
Globally enables ARP Spoofing Defense and configures sub-functions.
Configures defenses against network attacks.
Controls network access based on MAC addresses.
Filters packets based on rules involving service, source, destination, and time.
Manages user online behavior.
Configures behavior control features.
Configures web filtering rules using Web Group Filtering or URL Filtering.
Secures web access by blocking HTTP posts and file downloads.
Introduces Virtual Private Networks.
Configures IPSec VPN tunnels for secure site-to-site or remote access.
Sets up IPSec policies, including basic and advanced parameters.
Defines core IPSec policy settings like network mode, gateway, and pre-shared key.
Checks the status of established IPSec VPN tunnels through the IPSec SA list.
Configures L2TP VPN tunnels for secure remote access.
Creates IP address pools for L2TP VPN clients, specifying name and IP range.
Sets up the router as an L2TP server, defining WAN port and encryption settings.
Configures the router as an L2TP client for establishing a VPN tunnel.
Configures PPTP VPN tunnels for secure remote access.
Configures Dynamic DNS settings for various providers.
To Next Page
