Vacon 20 SERIES User Manual

vacon • 0
Service support: find your nearest Vacon service center at www.vacon.com
INDEX
Document ID: DPD01381B
Rev. B
Version release date: 5.12.13
Corresponds to application package ACIT1124V101.vcx
1. BH Application ................................................................................................. 2
1.1 Specific functions of Vacon BH application ...................................................................... 2
1.2 ASi Board Diagnostic........................................................................................................3
1.3 Description of the terminals (D-option with AS-interface) .............................................. 4
1.3.1 MU2 connections............................................................................................................... 4
1.3.2 MU3 connections............................................................................................................... 6
1.4 Description of the terminals (D-option with Profibus) ..................................................... 8
1.4.1 MU2 connections............................................................................................................... 8
1.4.2 MU3 connections............................................................................................................. 10
2. Description of Groups .................................................................................... 12
2.1 Monitor group: menu MON ............................................................................................. 12
2.1.1 ASi.................................................................................................................................... 12
2.1.2 Sensors............................................................................................................................ 12
2.1.3 Motor ............................................................................................................................... 12
2.1.4 Drive ................................................................................................................................ 13
2.2 Parameter Groups: Menu PAR ....................................................................................... 14
2.2.1 Group Motor settings: Menu PAR G1 .............................................................................. 15
2.2.2 Group Start/Stop Settings: Menu PAR G2....................................................................... 16
2.2.3 Group References: Menu PAR G3 ................................................................................... 17
2.2.4 Group Ramps: Menu PAR G4 .......................................................................................... 19
2.2.5 Group Input functions: Menu PAR G5 ............................................................................ 20
2.2.6 Group Output functions: Menu PAR G6........................................................................... 21
2.2.7 Group Mechanical brake: Menu PAR G7......................................................................... 22
2.2.8 Group Supervisions: Menu PAR G8................................................................................. 23
2.2.9 Group Motor Control: Menu PAR G9............................................................................... 24
2.2.10 Group Protections: Menu PAR G10................................................................................. 25
2.2.11 Group Automatic reset: Menu PAR G11.......................................................................... 27
2.2.12 Group Non-ASi fieldbus: Menu PAR G12 ........................................................................ 28
2.2.13 Group Analogue output: Menu Par G13 .......................................................................... 29
2.2.14 Group User interface: Menu Par G14.............................................................................. 29
2.3 System parameters, Faults and History faults: Menu FLT ............................................ 30
2.4 Keypad Reference: Menu REF ........................................................................................ 32
3. Parameter description................................................................................... 34
3.1 Motor Settings ................................................................................................................. 34
3.2 Start/Stop settings ..........................................................................................................36
3.3 References ...................................................................................................................... 38
3.4 Ramps.............................................................................................................................. 40
3.5 Input functions................................................................................................................. 42
3.6 Output functions .............................................................................................................. 44
3.7 Mechanical brake ............................................................................................................ 46
3.8 Supervisions .................................................................................................................... 47
3.9 Motor control................................................................................................................... 48
3.10 Protections ...................................................................................................................... 52
3.11 Automatic reset............................................................................................................... 58
3.12 Non-ASi fieldbus ............................................................................................................. 59
3.12.1 Modbus fieldbus mapping............................................................................................... 60
3.13 Analogue Output.............................................................................................................. 62
3.14 User interface.................................................................................................................. 62

Vacon 20 SERIES Specifications

General

Output Voltage	0 to Input Voltage
Storage Temperature	-40°C to +70°C
Dimensions	Varies by model
Weight	Varies by model
Power Range	0.25 kW to 18.5 kW
Voltage Range	200 V to 480 V
Control Method	Sensorless vector control
Protection Class	IP20
Ambient Temperature	-10°C to +50°C
Communication Options	Modbus, CANopen
EMC Filter	Integrated
STO (Safe Torque Off)	Yes
Input Voltage	208-240 V, 380-480 V
Protection Features	Overvoltage, Undervoltage, Overcurrent, Overtemperature
Operating Temperature	-10°C to +50°C
Humidity	5% to 95% non-condensing