WAGO-I/O-SYSTEM 750 Important Notes 13
750-461 2AI Pt100/RTD
Manual
Version 1.4.1
Pos: 18.12 /Alle Seri en (Allgemeine Module)/ Überschriften/Eben e 2/Sicherheitshi nweise - Überschri ft 2 @ 6\mod_1260180299987_21. docx @ 46724 @ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 18.13 /Alle Seri en (Allgemeine Module)/ Sicherheits- und sons tige Hinweise/Einlei tung Sicherheitshi nweise Hardware @ 6\mod_1260 180170493_21.doc x @ 46720 @ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 18.14.1 /Alle Ser ien (Allgemeine Module) /Sicherheits- und son stige Hinweise/ Gefahr/Gefahr: Nic ht an Geräten unter Spannung ar beiten! @ 6\mod_126018036 5327_21.docx @ 46727 @ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 18.14.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Er läuterungen (alte Struk tur)/Sicherhei ts- und sonstige Hinweise/ Gefahr/Gefahr : Einbau 0750- xxxx nur in Gehäusen, Schr änken oder elektrisc hen Betriebsräumen! @ 6\mod_ 1260180556692_21.doc x @ 46731 @ @ 1
Install the device only in appropriate housings, cabinets or in electrical
operation rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Pos: null /Alle Serien ( Allgemeine Module)/ Sicherheits- und sons tige Hinweise/Gefahr/ Gefahr: Trennvorr ichtung und Überstro mschutz @ 33\mod_1543915978 439_21.docx @ 512267 @ @ 1
Ensure disconnect and overcurrent protection!
The device is intended for installation in automation technology systems.
Disconnect protection is not integrated. Connected systems must be protected by
a fuse.
Provide suitable disconnect and overcurrent protection on the system side!
Pos: 18.14.4 /Alle Ser ien (Allgemeine Module) /Sicherheits- und son stige Hinweise/ Gefahr/Gefahr: Unfall verhütungsvorschr iften beachten! @ 6\mod_1 260180657000_21.doc x @ 46735 @ @ 1
Pos: 18.14.5 /Alle Ser ien (Allgemeine Module) /Sicherheits- und son stige Hinweise/ Gefahr/Gefahr: Auf normgerechten Anschluss ac hten! @ 6\mod_12601807 53479_21.docx @ 46739 @ @ 1
Ensure a standard connection!
To minimize any hazardous situations resulting in personal injury or to avoid
failures in your system, the data and power supply lines shall be installed
according to standards, with careful attention given to ensuring the correct
terminal assignment. Always adhere to the EMC directives applicable to your
application.
Pos: null /Alle Serien ( Allgemeine Module)/ Sicherheits- und sonstige Hinweise/Ac htung/Achtung: Ei nwandfreie Kontaktier ung zur Tragschiene gewä hrleisten! @ 34\mod_15504 81407638_21.doc x @ 530599 @ @ 1
Ensure proper contact with the DIN-rail!
Proper electrical contact between the DIN-rail and device is necessary to
maintain the EMC characteristics and function of the device.
Pos: 18.15.2 /Alle Ser ien (Allgemeine Module) /Sicherheits- und son stige Hinweise/Ac htung/Achtung: Defek te oder beschädigte Ger äte austauschen! @ 6\mod_1 260180857358_21.d ocx @ 46743 @ @ 1