Xtralis VESDA-E VEP-A10-P - Removing Door Hinge Pin a; Detaching Door

114 pages

Save Page as PDF

To Next Page

To Previous Page

VESDA-EVEP-A10-P Product Guide

24 www.xtralis.com

Figure4-9: Removing door hinge pin A

Figure4-10: Detaching door

Main Page

General Warning3
Liability3
Total Liability3
Miscellaneous3
Table of Contents7
Introduction9
Features9
VESDA-E VEP-A10-P Aspirating Smoke Detector9
Product Information11
Detector Components11
How the VEP-A10-P Works11
Front Panel12
Status LEDS12
RESET / DISABLE Button12
LED Indicators12
Touch Screen13
Main Screen13
Airflow Screen13
Main Screen - System with Faults13
Status Screen14
Navigation14
Internal Buttons14
Autoconfig14
Communication Ports15
Usb15
Ethernet15
Wifi15
Vesdanet15
Gateway Function of the VEP-A10-P16
Specifications17
Dimensions19
Front, Top, Bottom and Side Dimensions19
Rear Dimensions with Mounting Bracket20
Rear Dimensions with Hole Locations for Direct Mounting21
Pipe Network Design and Installation23
Design Considerations23
Installation Considerations23
Pipe Inlets23
Managing the Exhaust Air24
Pipe Inlet Port Numbering24
Imperial Pipe Adaptor (VSP-961)24
Installation25
Prepare the Detector25
Remove Cable and Pipe Inlet Plugs25
Mounting26
Sideways Orientation26
Mounting Location26
Inverting the Detector27
Detector with Fascia Removed27
Tabs Used to Remove Top and Bottom Cover28
Detaching the Tethers28
Detector with Tethers Detached29
Removing Door Hinge Pin a30
Detaching Door30
Rotate Detector and Door and Move Door to Right Side of Fascia31
Replacing the Door Hinge Pin32
Correct Positioning of Door Hinge Pin When Fully in Place33
Re-Attach Tethers at Circled Positions33
Position the Tethers and Pull up to Attach34
Mounting the Detector with the Mounting Bracket35
Position Mounting Bracket in Line with Pipes35
Mark Keyholes35
Tighten Screws35
Mounting Bracket36
Mounting the Detector36
Locking Screw36
Mounting the Detector Using the Mounting Template37
Position Mounting Template37
Insert Mounting Screws37
Position Conduit and Pipes38
Mount the Detector38
Position Detector over Screw38
Slide Detector to the Left39
Position Detector on the Second Screw39
Rotate the Detector39
Wiring41
Cabling Inlets41
Socket Locations42
Power Source42
Power to Multiple Detectors43
Compliance43
Vesdanet43
Example Closed Loop Vesdanet Network44
Closed Loop for Standalone Detectors with Vesdanet Capability44
Relays45
Fault and Fire 1 Relay Terminals45
Fire 1 Relay45
Typical Relay Operation45
Unmonitored General Purpose Input (GPI)47
Monitored General Purpose Input (GPI) Wiring47
Typical Wiring to Fire Alarm Control Panel (FACP)48
Typical Wiring to Addressable Loop Module48
Typical Wiring to a Fire Panel with EOL48
Input/Output Loop Module with EOL48
Typical Wiring for Monitored GPI for PSU Monitoring49
Power Supply Connection Diagram49
Specify Backup Battery50
Calculating the Size of Backup Battery50
Powering up51
Installation Checklist52
Preliminary System Check53
Configuration55
Communication between Xtralis VSC and the Detector55
Defining Connection Profiles in Xtralis VSC55
Connection Profile for a Detector55
Adding a USB Connection56
Add Connection56
Adding an Ethernet or Wifi Connection57
Select Ethernet57
Enter a Connection Name57
Connecting to the Detector59
Connecting to a Detector Via USB59
Connect to a Detector Using Xtralis VSC59
Connecting to a Detector Via Ethernet59
Connecting to a Detector Via Wifi60
Enabling Wifi Connection60
Connecting to a Detector Via Wifi Using a Router60
Connection to a Detector Via Vesdanet61
Access the VEP-A10-P61
Security62
Wifi and Ethernet Authentication62
Access Control62
User Access Levels62
Commands63
Detector Commands63
Configuration Options66
General Options66
Vesdanet Options66
Vesdanet Communications Options67
Ethernet Options67
Dynamic IP Address Configuration67
Static IP Address Configuration68
Wifi Options69
Wifi Network Connection Parameters69
Wifi IP Configuration Parameters69
Smoke Threshold Options70
Changeover70
Airflow Options71
Filter Option71
Referencing Options73
General Purpose Inputs Options74
GPI Operation74
Unmonitored GPI74
Monitored GPI74
Relay Options77
Relay Assignments77
Normally Energized77
Button Lockout Options78
Factory Default Settings79
Default Settings79
Commissioning83
Prior to Commissioning the Detector83
Autolearn Smoke83
Autolearn Flow84
Autolearn Smoke Range84
Commissioning Smoke Test84
Maintenance85
Standby85
Recommended Maintenance Schedule for the VEP-A10-P Detector85
Open the Door86
Replacing the Filter87
Remove the Filter87
Release Filter87
Tilt Filter Towards the Left-Hand Side of the Detector88
Remove Filter88
Reinstall the Filter88
Engage Hinge Pins89
Remove the Fascia90
Wrist Strap Application90
Fascia Removal - Remove Screws91
Fascia Hanging on Two Tethers91
Replacing the Aspirator92
Remove the Aspirator92
Disconnect the Aspirator Cable92
Remove Aspirator Mounting Screws92
Reinstall the Replacement Aspirator93
Remove Aspirator from the Detector93
Replacing the Smoke Detection Chamber94
Remove the Smoke Detection Chamber94
Undo Chamber Retaining Screws94
Disconnect Chamber Loom95
Remove the Chamber from the Detector Base95
Installing the Replacement Smoke Detector Chamber96
Position the Gray Loom96
Position the Chamber Looms96
Install the Chamber97
Replacing the Sampling Module98
Removing the Sampling Module98
Disconnect the Sampling Module Cable98
Release the Sampling Module Cable99
Undo Sampling Module Screws100
Installing a Replacement Sampling Module101
Remove Sampling Module101
Reinstall Sampling Module101
Spare Parts102
Fault Reporting through Relays103
Troubleshooting with the Front Panel Display103
Fault Indicators103
Troubleshooting with Xtralis VSC104
A Commissioning Forms105
VEP-A10-P Detector Commissioning Configuration107
ASPIRE Data107
Smoke Test107
Air Sampling Test Results107
Glossary109
Index111

Xtralis VESDA-E VEP-A10-P - Removing Door Hinge Pin a; Detaching Door

Table of Contents

Related product manuals