Yamaha SRX700D - High Altitude Settings

SPEC
9-13
MAINTENANCE SPECIFICATIONS
Altitude
MJ #1 #151.3
MJ #2#3 #150
PJ #42.5
JN 3
PS 1 1/8
MJ #1 #148.8
MJ #2#3 #147.5
PJ #42.5
JN 3
PS 1 1/8
MJ #1 #146.3
MJ #2#3 #145
PJ #45
JN 3
PS 1 1/4
MJ #1 #142.5
MJ #2#3 #141.3
PJ #45
JN 2.5
PS 1 1/2
MJ #1 #140
MJ #2#3 #138.8
PJ #47.5
JN 2.5
PS 1 5/8
MJ #1 #137.5
MJ #2#3 #136.3
PJ #50
JN 2.5
PS 1 3/4
MJ #1 #148.8
MJ #2#3 #147.5
PJ #40
JN 3
PS 1 1/8
MJ #1 #146.3
MJ #2#3 #145
PJ #40
JN 3
PS 1 1/8
MJ #1 #143.8
MJ #2#3 #142.5
PJ #42.5
JN 3
PS 1 1/4
MJ #1 #140
MJ #2#3 #138.8
PJ #42.5
JN 2.5
PS 1 1/2
MJ #1 #137.5
MJ #2#3 #136.3
PJ #45
JN 2.5
PS 1 5/8
MJ #1 #135
MJ #2#3 #133.8
PJ #47.5
JN 2
PS 1 3/4
MJ #1 #147.5
MJ #2#3 #146.3
PJ #37.5
JN 3
PS 1
MJ #1 #145
MJ #2#3 #143.8
PJ #40
JN 3
PS 1
MJ #1 #142.5
MJ #2#3 #141.8
PJ #40
JN 3
PS 1 1/8
MJ #1 #138.8
MJ #2#3 #137.5
PJ #42.5
JN 2.5
PS 1 3/8
MJ #1 #136.3
MJ #2#3 #135
PJ #45
JN 2.5
PS 1 1/2
MJ #1 #133.8
MJ #2#3 #132.5
PJ #47.5
JN 2
PS 1 5/8
MJ #1 #150
MJ #2#3 #148.8
PJ #40
JN 3
PS 1 1/8
MJ #1 #147.5
MJ #2#3 #146.3
PJ #42.5
JN 3
PS 1 1/8
MJ #1 #145
MJ #2#3 #143.8
PJ #42.5
JN 3
PS 1 1/4
MJ #1 #141.3
MJ #2#3 #140
PJ #45
JN 2.5
PS 1 1/2
MJ #1 #138.8
MJ #2#3 #137.5
PJ #47.5
JN 2.5
PS 1 5/8
MJ #1 #136.3
MJ #2#3 #135
PJ #50
JN 2.5
PS 1 3/4
MJ #1 #152.5
MJ #2#3 #151.3
PJ #42.5
JN 3.5
PS 1 1/8
MJ #1 #150
MJ #2#3 #148.8
PJ #45
JN 3
PS 1 1/8
MJ #1 #147.5
MJ #2#3 #146.3
PJ #45
JN 3
PS 1 1/4
MJ #1 #143.8
MJ #2#3 #142.5
PJ #47.5
JN 2.5
PS 1 1/2
MJ #1 #141.3
MJ #2#3 #140
PJ #50
JN 2.5
PS 1 5/8
MJ #1 #138.8
MJ #2#3 #137.5
PJ #52.5
JN 2.5
PS 1 3/4
[Production spec] MJ#1: #147.5 MJ#2, 3: #146.3 PJ: #42.5 JN: 6GM26-3 PAJ: 1.0 PS: 1-1/8
#: Main jet number JN: Jet needle clip position PS: Pilot screw turns out PJ: Pilot jet number
HIGH ALTITUDE SETTINGS
SRX700/700S
Tempera-
ture
0 ~ 250 m
(0 ~ 800 ft)
250 ~ 750 m
(800~ 2,500 ft)
750 ~ 1,500 m
(2,500 ~ 4,900 ft)
1,500 ~ 2,000 m
(4,900 ~ 6,600 ft)
2,000 ~ 2,500 m
(6,600 ~ 8,200 ft)
2,500 ~ 3,000 m
(8,300 ~ 10,000 ft)
NOTE:
• Jet needle (JN) position
Refer to the following information for the Jet needle shims installation.
JN:2(STD) JN:1.5 JN:1 JN:0.5
• Oxygenated fuels
Use one size larger Main Jet than specified.
–40°C –29°C –18°C–7°C4°C16°C
(–40°F) (–20°F) (0°F) (20°F) (40°F) (60°F)