11 Drive Control, Duty Modes, and Programming
YASKAWA TOEPC71061737B GA800 Drive Installation & Primary Operation 71
No.
(Hex.)
Name Description
C2-01
(020B)
S-Curve Time @ Start of Accel
Sets the S-curve acceleration time at start.
C2-02
(020C)
S-Curve Time @ End of Accel
Sets the S-curve acceleration time at completion.
C2-03
(020D)
S-Curve Time @ Start of Decel
Sets the S-curve deceleration time at start.
C2-04
(020E)
S-Curve Time @ End of Decel
Sets the S-curve deceleration time at completion.
C6-01
(0223)
Normal / Heavy Duty Selection
Sets the drive duty rating.
0 : Heavy Duty Rating
1 : Normal Duty Rating
C6-02
(0224)
Carrier Frequency Selection
Sets the carrier frequency for the transistors in the drive.
1 : 2.0 kHz
2 : 5.0 kHz (4.0 kHz AOLV/PM)
3 : 8.0 kHz (6.0 kHz AOLV/PM)
4 : 10.0 kHz (8.0 kHz AOLV/PM)
5 : 12.5 kHz (10.0 kHz AOLV/PM)
6 : 15.0 kHz (12.0 kHz AOLV/PM)
7 : Swing PWM1 (Audible Sound 1)
8 : Swing PWM2 (Audible Sound 2)
9 : Swing PWM3 (Audible Sound 3)
A : Swing PWM4 (Audible Sound 4)
F : User Defined (C6-03 to C6-05)
d1-01 to d1-16
(0280 - 0291)
RUN
Reference 1 to 16
Sets the frequency reference in the units from o1-03 [Frequency Display Unit Selection].
d1-17
(0292)
RUN
Jog Reference
Sets the Jog frequency reference in the units from o1-03 [Frequency Display Unit Selection]. Set H1-xx = 6 [MFDI
Function Select = Jog Reference Selection] to use the Jog frequency reference.
d2-01
(0289)
Frequency Reference Upper Limit
Sets maximum limit for all frequency references. The maximum output frequency is 100%.
d2-02
(028A)
Frequency Reference Lower Limit
Sets minimum limit for all frequency references. The maximum output frequency is 100%.
E1-01
(0300)
Input AC Supply Voltage
Sets the drive input voltage.
E1-04
(0303)
Maximum Output Frequency
Sets the maximum output frequency for the V/f pattern.
E1-05
(0304)
Maximum Output Voltage
Sets the maximum output voltage for the V/f pattern.
E1-06
(0305)
Base Frequency
Sets the base frequency for the V/f pattern.
E1-09
(0308)
Minimum Output Frequency
Sets the minimum output frequency for the V/f pattern.
E2-01
(030E)
Motor Rated Current (FLA)
Sets the motor rated current in amps.
E2-11
(0318)
Motor Rated Power
Sets the motor rated output in the units from o1-58 [Motor Power Unit Selection].
H1-01 - H1-08
(0438, 0439, 0400 -
0405)
Terminal S1 to S8 Function
Selection
Sets the functions for MFDI terminals S1 to S8.
H2-01
(040B)
Term M1-M2 Function Selection
Sets the function for MFDO terminal M1-M2.
H2-02
(040C)
Term M3-M4 Function Selection
Sets the function for MFDO terminal M3-M4.
To Next Page
Loading...
