Yealink SIP-T43U Administrator's Guide

Administrator’s Guide for SIP-T2 Series/T4 Series/T5 Series/CP920 IP Phones
144
Handset Firmware Upgrade Configuration
The following table lists the parameters you can use to upgrade handset firmware.
Parameter
over_the_air.url <y0000000000xx>.cfg
Description
It configures the access URL of the handset firmware file.
Note: The priority of parameter “over_the_air.url” is lower than “over_the_air.url.w56h”/over_the_air-
.url.w53h/“over_the_air.url.w52h”.
Permitted
Values
URL within 511 characters
Default
Blank
Web UI
Settings > Upgrade > Select and update handset firmware.
Parameter
over_the_air.url.w56h <y0000000000xx>.cfg
Description
It configures the access URL of the W56H handset firmware file.
Note: The priority of parameter “over_the_air.url.w56h” is higher than “over_the_air.url”.
Permitted
Values
URL within 511 characters
Default
Blank
Parameter
over_the_air.url.cp930w <y0000000000xx>.cfg
Description
It configures the access URL of the CP930W phone firmware file.
Note: The priority of parameter “over_the_air.url.cp930w” is higher than “over_the_air.url”.
Permitted
Values
URL within 512 characters
Default
Blank
Parameter
over_the_air.handset_tip <y0000000000xx>.cfg
Description
It enables or disables to pop up a tip when upgrading the handset firmware from the provisioning
server.
Note: It works only if “over_the_air.base_trigger” and “over_the_air.handset_trigger” are set to 0 (Dis-
abled).
Permitted
Values
0-Disabled
1-Enabled, the handset will pop up the message “Handset has a new firmware, update now?”.
Default
1
Supported
Devices
All handsets except DD phones
Parameter
over_the_air.handset_trigger <y0000000000xx>.cfg
Description
It enables or disables to upgrade the handset firmware compulsively when the handset is registered
to a phone or turned on successfully.
It is only applicable when the current handset firmware is different from the one on the provisioning
server.
Permitted
Values
0-Disabled, if “over_the_air.handset_tip” is set to 1 (Enabled), it will pop up a tip on the handset to
notify the user of firmware upgrade. If “over_the_air.handset_tip” is set to 0, you may go to Settings >
Upgrade Firmware on the handset to trigger the upgrading manually.
1-Enabled, it will upgrade the handset firmware compulsively without a pop-up tip on the handset.

Yealink SIP-T43U Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Gray
Wall mountable	Yes
Sustainability certificates	REACH, RoHS
AC adapter input voltage	100 - 240 V
AC adapter output current	1.2 A
AC adapter output voltage	5 V
Power consumption (typical)	2.2 W
Bluetooth version	4.1
Networking standards	IEEE 802.1Q, IEEE 802.1p, IEEE 802.1x, IEEE 802.3af
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet LAN interface type	Gigabit Ethernet
Supported network protocols	FTP/TFTP/HTTP/HTTPS, IPv6, LLDP/CDP/DHCP VLAN
USB 2.0 ports quantity	2
Lines quantity	12 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	12
Voice codecs	AGC, AJB, AMR-NB, AMR-WB, G.711Mu, G.711a, G.723.1, G.726, G.729ab, OPUS, PLC, VAD, iLBC
Number of handles included	1 pc(s)
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %
Display diagonal	3.7 \
Display resolution	360 x 160 pixels
Dual-Tone Multi-Frequency (DTMF) modes	In-band, Out-of band, SIP info
Harmonized System (HS) code	85171800

Weight and Dimensions

Depth	206.2 mm
Width	224.9 mm
Height	174.9 mm
Package depth	223 mm
Package width	246 mm
Package height	120 mm