Yealink SIP-T43U Administrator's Guide

Administrator’s Guide for SIP-T2 Series/T4 Series/T5 Series/CP920 IP Phones
361
takes precedence over that configured by this parameter.
Permitted
Values
0-prevent users from entering a number and immediately dial out the entered numbers
1-the dialing will fail and the phone screen will prompt “Forbidden Number”
2-allow users to accumulate digits and dispatch call manually with the send key or automatically dial
out the entered number after a certain period of time configured by the parameter “dial-
plan.digitmap.interdigit_long_timer”
Default
0
Parameter
dialplan.digitmap.active.on_hook_dialing <y0000000000xx>.cfg
Description
It enables or disables the entered numbers to match the predefined string of the digit map in real time.
It is only applicable to the on-hook dialing.
Note: It works only if “dialplan.digitmap.enable” or “account.X.dialplan.digitmap.enable” is set to 1
(Enabled). The value configured by the parameter “account.X.dialplan.digitmap.active.on_hook_dial-
ing” takes precedence over that configured by this parameter.
Permitted
Values
0-Disabled
1-Enabled
Default
0
Parameter
dialplan.digitmap.apply_to.on_hook_dial <y0000000000xx>.cfg
Description
It enables or disables the entered number to match the predefined string of the digit map after press-
ing a send key when dialing on-hook or pressing the DSS key (for example, speed dial, BLF or prefix
key).
Note: It works only if “dialplan.digitmap.enable” or “account.X.dialplan.digitmap.enable” is set to 1
(Enabled). The value configured by the parameter “account.X.dialplan.digitmap.apply_to.on_hook_
dial” takes precedence over that configured by this parameter.
Permitted
Values
0-Disabled
1-Enabled
Default
1
Parameter
dialplan.digitmap.apply_to.directory_dial <y0000000000xx>.cfg
Description
It enables or disables the digit map to be applied to the numbers dialed from the directory.
Note: It works only if “dialplan.digitmap.enable” or “account.X.dialplan.digitmap.enable” is set to 1
(Enabled). The value configured by the parameter “account.X.dialplan.digitmap.apply_to.directory_
dial” takes precedence over that configured by this parameter.
Permitted
Values
0-Disabled
1-Enabled
Default
1
Parameter
dialplan.digitmap.apply_to.history_dial <y0000000000xx>.cfg
Description
It enables or disables the digit map to be applied to the numbers (received calls or missed calls)
dialed from the call history list.
Note: It works only if “dialplan.digitmap.enable” or “account.X.dialplan.digitmap.enable” is set to 1
(Enabled). The value configured by the parameter “account.X.dialplan.digitmap.apply_to.history_dial”
takes precedence over that configured by this parameter.
Permitted
Values
0-Disabled
1-Enabled
Default
0

Yealink SIP-T43U Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Gray
Wall mountable	Yes
Sustainability certificates	REACH, RoHS
AC adapter input voltage	100 - 240 V
AC adapter output current	1.2 A
AC adapter output voltage	5 V
Power consumption (typical)	2.2 W
Bluetooth version	4.1
Networking standards	IEEE 802.1Q, IEEE 802.1p, IEEE 802.1x, IEEE 802.3af
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet LAN interface type	Gigabit Ethernet
Supported network protocols	FTP/TFTP/HTTP/HTTPS, IPv6, LLDP/CDP/DHCP VLAN
USB 2.0 ports quantity	2
Lines quantity	12 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	12
Voice codecs	AGC, AJB, AMR-NB, AMR-WB, G.711Mu, G.711a, G.723.1, G.726, G.729ab, OPUS, PLC, VAD, iLBC
Number of handles included	1 pc(s)
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %
Display diagonal	3.7 \
Display resolution	360 x 160 pixels
Dual-Tone Multi-Frequency (DTMF) modes	In-band, Out-of band, SIP info
Harmonized System (HS) code	85171800

Weight and Dimensions

Depth	206.2 mm
Width	224.9 mm
Height	174.9 mm
Package depth	223 mm
Package width	246 mm
Package height	120 mm