YOKOGAWA DL9040

5-127
IM 701310-17E
Commands
1
2
3
4
5
6
App
Index
:MEASure:TRACe<x>:AREA<x>:<Parameter>:
{MAXimum|MEAN|MINimum|SDEViation}?
Function Queries the statistical value of the waveform
parameter.
Syntax
:MEASure:TRACe<x>:AREA<x>:<Parameter>:
{MAXimum|MEAN|MINimum|SDEViation}?
<x> of TRACe<x> = 1 to 8
<x> of AREA<x> = 1 or 2
<Parameter> = {BURSt|CMEan|COUNt|CRMS|
CSDeviation|DELay|DT|DUTYcycle|FALL|
FREQuency|HIGH|HILow|LOW|MAXimum|MEAN|
MINimum|NOVershoot|NWIDth|PERFrequency|
PERiod|POVershoot|PTOPeak|PWIDth|RISE|
RMS|SDEViation|TYCInteg|TYINteg|V1|V2}
Example (The following is an example for the maximum value.)
:MEASURE:TRACE1:AREA1:MAXIMUM:
MAXIMUM? -> :MEASURE:TRACE1:AREA1:
MAXIMUM:MAXIMUM 1.000E+00
:MEASure:TRACe<x>:AREA<x>:<Parameter>:
STATe
Function Turns ON/OFF the waveform parameter or queries
the current setting.
Syntax
:MEASure:TRACe<x>:AREA<x>:<Parameter>:
STATe {<Boolean>}
:MEASure:TRACe<x>:AREA<x>:<Parameter>:
STATe?
<x> of TRACe<x> = 1 to 8
<x> of AREA<x> = 1 or 2
<Parameter> = {BURSt|CMEan|COUNt|CRMS|
CSDeviation|DELay|DT|DUTYcycle|FALL|
FREQuency|HIGH|HILow|LOW|MAXimum|MEAN|
MINimum|NOVershoot|NWIDth|PERFrequency|
PERiod|POVershoot|PTOPeak|PWIDth|RISE|
RMS|SDEViation|TYCInteg|TYINteg|V1|V2}
Example (The following is an example for the maximum value
of trace 1 and area 1.)
:MEASURE:TRACE1:AREA1:MAXIMUM:STATE ON
:MEASURE:TRACE1:AREA1:MAXIMUM:STATE?
-> :MEASURE:TRACE1:AREA1:MAXIMUM:
STATE 1
:MEASure:TRACe<x>:AREA<x>:<Parameter>?
Function Queries all settings related to the waveform
parameter.
Syntax
:MEASure:TRACe<x>:AREA<x>:<Parameter>?
<x> of TRACe<x> = 1 to 8
<x> of AREA<x> = 1 or 2
<Parameter> = {BURSt|CMEan|COUNt|CRMS|
CSDeviation|DELay|DT|DUTYcycle|FALL|
FREQuency|HIGH|HILow|LOW|MAXimum|MEAN|
MINimum|NOVershoot|NWIDth|PERFrequency|
PERiod|POVershoot|PTOPeak|PWIDth|RISE|
RMS|SDEViation|TYCInteg|TYINteg|V1|V2}
Example (The following is an example for the maximum value
of trace 1 and area 1.)
:MEASURE:TRACE1:AREA1:MAXIMUM?
-> :MEASURE:TRACE1:AREA1:MAXIMUM:
STATE 0
:MEASure:TRACe<x>:AREA<x>:<Parameter>:
COUNt?
Function Queries the continuous statistical processing count of
the waveform parameter.
Syntax
:MEASure:TRACe<x>:AREA<x>:<Parameter>:
COUNt?
<x> of TRACe<x> = 1 to 8
<x> of AREA<x> = 1 or 2
<Parameter> = {BURSt|CMEan|COUNt|CRMS|
CSDeviation|DELay|DT|DUTYcycle|FALL|
FREQuency|HIGH|HILow|LOW|MAXimum|MEAN|
MINimum|NOVershoot|NWIDth|PERFrequency|
PERiod|POVershoot|PTOPeak|PWIDth|RISE|
RMS|SDEViation|TYCInteg|TYINteg|V1|V2}
Example (The following is an example for the maximum value
of trace 1 and area 1.)
:MEASURE:TRACE1:AREA1:MAXIMUM:COUNT?
-> :MEASURE:TRACE1:AREA1:MAXIMUM:
COUNT 0
5.18 MEASure Group