Command Function Page
:TELecomtest:MASK?
Queries all settings related to the mask test. 5-145
:TELecomtest:MASK:ELEMent<x>?
Queries all settings related to the element used in the mask test. 5-145
:TELecomtest:MASK:ELEMent<x>:
ALL
Turns ON/OFF all items of the element. 5-145
:TELecomtest:MASK:ELEMent<x>:
PSPCount? (Sample Point Count %)
Queries the settings related to the error rate for the number of sampled data
points of the element.
5-145
:TELecomtest:MASK:ELEMent<x>:
PSPCount:STATe
Turns ON/OFF the measurement of the error rate for the number of sampled
data points of the element or queries the current setting.
5-145
:TELecomtest:MASK:ELEMent<x>:
PSPCount:VALue?
Queries the error rate for the number of sampled data points of the element. 5-145
:TELecomtest:MASK:ELEMent<x>:
PWCount? (Wave Count %)
Queries the settings related to the error rate for the acquisition count of the
element.
5-145
:TELecomtest:MASK:ELEMent<x>:
PWCount:STATe
Turns ON/OFF the measurement of the error rate for the acquisition count of
the element or queries the current setting.
5-146
:TELecomtest:MASK:ELEMent<x>:
PWCount:VALue?
Queries the error rate for the acquisition count of the element. 5-146
:TELecomtest:MASK:ELEMent<x>:
SPCount? (Sample Point Count)
Queries the settings related to the number of sampled data points for the
element that results in error.
5-146
:TELecomtest:MASK:ELEMent<x>:
SPCount:STATe
Turns ON/OFF the measurement of the number of sampled data points for
the element that results in error or queries the current setting.
5-146
:TELecomtest:MASK:ELEMent<x>:
SPCount:VALue?
Queries the number of sampled data points for the element that resulted in
error.
5-146
:TELecomtest:MASK:ELEMent<x>:
WCOunt?(Wave Count)
Queries the settings related to the acquisition count for the element that
results in error.
5-146
:TELecomtest:MASK:ELEMent<x>:
WCOunt:STATe
Turns ON/OFF the measurement of the acquisition count for the element that
results in error or queries the current setting.
5-146
:TELecomtest:MASK:ELEMent<x>:
WCOunt:VALue?
Queries the acquisition count for the element that resulted in error. 5-146
:TELecomtest:MMODe
Turns ON/OFF the computed waveform or queries the current setting. 5-147
:TELecomtest:TRACe
Sets the source trace of the telecom test or queries the current setting. 5-147
:TELecomtest:TRANge (Time Range)
Sets the measurement range of the telecom test or queries the current
setting.
5-147
:TELecomtest:WINDow
Sets the measurement source window of the telecom test or queries the
current setting.
5-147
TIMebase Group
:TIMebase?
Queries all settings related to the time base. 5-148
:TIMebase:SRATe? (Sample RATE)
Queries the sample rate or queries the current setting. 5-148
:TIMebase:TDIV
Sets the T/div value or queries the current setting. 5-148
TRIGger Group
:TRIGger?
Queries all settings related to the trigger. 5-149
:TRIGger:ACTion?
Queries all settings related to action-on-trigger. 5-149
:TRIGger:ACTion:ACQCount
Sets the action count of action-on-trigger or queries the current setting. 5-149
:TRIGger:ACTion:BUZZer
Sets whether to sound a buzzer when an action is activated or queries the
current setting.
5-149
:TRIGger:ACTion:HCOPy
Sets whether or not to output screen image data (ON/OFF) when an action
is activated, or queries the current setting.
5-149
:TRIGger:ACTion:MAIL?
Queries all settings related to the mail transmission when an action is
activated.
5-149
:TRIGger:ACTion:MAIL:INTerval
Sets the interval at which to send mail when an action is activated or queries
the current setting.
5-150
:TRIGger:ACTion:MAIL:MODE
Sets whether to send mail when an action is activated or queries the current
setting.
5-150
:TRIGger:ACTion:MODE
Sets the action-on-trigger mode or queries the current setting. 5-150
:TRIGger:ACTion:SAVE
Sets whether to save the waveform data to the storage medium (ON/OFF)
when an action is activated or queries the current setting.
5-150
:TRIGger:ACTion:STARt
Starts the action-on-trigger. 5-150
:TRIGger:ACTion:STOP
Stops the action-on-trigger. 5-150
:TRIGger:CLOCk?
Queries all settings related to the clock channel. 5-150
:TRIGger:CLOCk:POLarity
Sets the polarity of the clock channel or queries the current setting. 5-150
:TRIGger:CLOCk:SOURce
Sets the source waveform of the clock channel or queries the current setting. 5-150
:TRIGger:DELay?
Queries all settings related to the trigger delay. 5-150
5.1 List of Commands
To Next Page
Loading...
