5-27
IM 701310-17E
Commands
Command Function Page
:TRIGger:EINTerval:EVENt<x>:
SPIBus:DATA<x>:DPOSition
Sets the pattern comparison start position of the data of the SPI bus trigger
or queries the current setting.
5-173
:TRIGger:EINTerval:EVENt<x>:
SPIBus:DATA<x>:HEXA<x>
Sets the data of the SPI bus trigger in hexadecimal notation. 5-173
:TRIGger:EINTerval:EVENt<x>:
SPIBus:DATA<x>:PATTern<x>
Sets the data of the SPI bus trigger in binary notation or queries the current
setting.
5-173
:TRIGger:EINTerval:EVENt<x>:
SPIBus:DATA<x>:SOURce
Sets the trace of the data of the SPI bus trigger or queries the current setting. 5-173
:TRIGger:EINTerval:EVENt<x>:
SPIBus:MODE
Sets the wiring system of the SPI bus trigger (three-wire or four-wire) or
queries the current setting.
5-174
:TRIGger:EINTerval:EVENt<x>:
STATe?
Queries all settings related to condition to be satisfied of the event. 5-174
:TRIGger:EINTerval:EVENt<x>:
STATe:CHANnel<x>
Sets the condition to be satisfied of the channel or queries the current
setting.
5-174
:TRIGger:EINTerval:EVENt<x>:
STATe:LOGic
Sets the logic of the condition to be satisfied or queries the current setting. 5-174
:TRIGger:EINTerval:EVENt<x>:
TYPE
Sets the trigger type of the event or queries the current setting. 5-174
:TRIGger:EINTerval:EVENt<x>:
WIDTh?
Queries all settings related to the pulse width trigger of the event. 5-174
:TRIGger:EINTerval:EVENt<x>:
WIDTh:MODE
Sets the determination mode of the pulse width trigger or queries the current
setting.
5-175
:TRIGger:EINTerval:EVENt<x>:
WIDTh:POLarity
Sets the polarity of the pulse width trigger or queries the current setting. 5-175
:TRIGger:EINTerval:EVENt<x>:
WIDTh:SOURce
Sets the trigger source of the pulse width trigger or queries the current
setting.
5-175
:TRIGger:EINTerval:EVENt<x>:
WIDTh:TIME<x>
Sets the pulse width of the pulse width trigger or queries the current setting. 5-175
:TRIGger:EINTerval:MODE
Sets the determination mode of the event interval or queries the current
setting.
5-175
:TRIGger:EINTerval:TIME<x>
Sets the interval time of the event interval or queries the current setting. 5-176
:TRIGger:EINTerval:TRY?
Queries all settings related to the event interval trial. 5-176
:TRIGger:EINTerval:TRY:MODE
Sets the trial mode or queries the current setting. 5-176
:TRIGger:EINTerval:TRY:SELect
Sets the source event of the trial mode or queries the current setting. 5-176
:TRIGger:ENHanced?
Queries all settings related to the enhanced trigger. 5-176
:TRIGger:ENHanced:CANBus?
Queries all settings related to the CAN bus signal trigger. 5-177
:TRIGger:ENHanced:CANBus:ACK
Sets the ACK condition of the CAN bus signal trigger or queries the current
setting.
5-177
:TRIGger:ENHanced:CANBus:BRATe
Sets the bit rate (data transfer rate) of the CAN bus signal trigger or queries
the current setting.
5-177
:TRIGger:ENHanced:CANBus:DATA?
Queries all settings related to the CAN bus signal trigger data. 5-177
:TRIGger:ENHanced:CANBus:DATA:
BORDer
Sets the byte order of the CAN bus signal trigger data or queries the current
setting.
5-177
:TRIGger:ENHanced:CANBus:DATA:
CONDition
Sets the data condition of the CAN bus signal trigger or queries the current
setting.
5-177
:TRIGger:ENHanced:CANBus:DATA:
DATA<x>
Sets the comparison data of the CAN bus signal trigger data or queries the
current setting.
5-178
:TRIGger:ENHanced:CANBus:DATA:
DLC
Sets the number of valid bytes (DLC) of the CAN bus signal trigger data or
queries the current setting.
5-178
:TRIGger:ENHanced:CANBus:DATA:
HEXA
Sets the CAN bus signal trigger data in hexadecimal notation. 5-178
:TRIGger:ENHanced:CANBus:DATA:
MSBLsb
Sets the MSB and LSB bits of the CAN bus signal trigger data or queries the
current setting.
5-178
:TRIGger:ENHanced:CANBus:DATA:
PATTern
Sets the CAN bus signal trigger data in binary notation or queries the current
setting.
5-178
:TRIGger:ENHanced:CANBus:DATA:
SIGN
Sets the sign of the CAN bus signal trigger data or queries the current
setting.
5-178
:TRIGger:ENHanced:CANBus:IDEXt?
Queries all settings related to the ID of the extended format of the CAN bus
signal trigger.
5-178
:TRIGger:ENHanced:CANBus:IDEXt:
HEXA
Sets the ID of the extended format of the CAN bus signal trigger in
hexadecimal notation.
5-179
:TRIGger:ENHanced:CANBus:IDEXt:
PATTern
Sets the ID of the extended format of the CAN bus signal trigger in binary
notation or queries the current setting.
5-179
:TRIGger:ENHanced:CANBus:IDOR?
Queries all settings related to the OR condition of the CAN bus signal trigger. 5-179
5.1 List of Commands
To Next Page
Loading...
