Command Function Page
:TRIGger:EINTerval:EVENt<x>:
I2CBus:SBHSmode?
Queries all settings related to the start byte and high speed mode of the I
2
C
bus trigger.
5-168
:TRIGger:EINTerval:EVENt<x>:
I2CBus:SBHSmode:TYPE
Sets the type of the start byte or high speed mode of the I
2
C bus trigger or
queries the current setting.
5-168
:TRIGger:EINTerval:EVENt<x>:
LINBus?
Queries all settings related to LIN bus signal triggers of each event. 5-168
:TRIGger:EINTerval:EVENt<x>:
LINBus:BRATe
Sets the LIN bus signal trigger bitrate (data transfer rate) or queries the
current setting.
5-168
:TRIGger:EINTerval:EVENt<x>:
LINBus:SOURce
Sets the LIN bus signal trigger source or queries the current setting. 5-169
:TRIGger:EINTerval:EVENt<x>:
SPATtern? (Serial Pattern)
Queries all settings related to the serial pattern trigger of the event. 5-169
:TRIGger:EINTerval:EVENt<x>:
SPATtern:BITRate
Sets the bit rate of the serial pattern trigger or queries the current setting. 5-169
:TRIGger:EINTerval:EVENt<x>:
SPATtern:CLEar
Clears the entire pattern of the serial pattern trigger (to don’t care). 5-169
:TRIGger:EINTerval:EVENt<x>:
SPATtern:CLOCk?
Queries all settings related to clock of the serial pattern trigger. 5-169
:TRIGger:EINTerval:EVENt<x>:
SPATtern:CLOCk:MODE
Enables/Disables the clock of the serial pattern trigger or queries the current
setting.
5-169
:TRIGger:EINTerval:EVENt<x>:
SPATtern:CLOCk:POLarity
Sets the polarity of the clock trace of the serial pattern trigger or queries the
current setting.
5-169
:TRIGger:EINTerval:EVENt<x>:
SPATtern:CLOCk:SOURce
Sets the clock trace of the serial pattern trigger or queries the current setting. 5-170
:TRIGger:EINTerval:EVENt<x>:
SPATtern:CS
Enables/Disables the chip select of the serial pattern trigger or queries the
current setting.
5-170
:TRIGger:EINTerval:EVENt<x>:
SPATtern:DATA?
Queries all settings related to data of the serial pattern trigger. 5-170
:TRIGger:EINTerval:EVENt<x>:
SPATtern:DATA:ACTive
Sets the active level of the data of the serial pattern trigger or queries the
current setting.
5-170
:TRIGger:EINTerval:EVENt<x>:
SPATtern:DATA:SOURce
Sets the data trace of the serial pattern trigger or queries the current setting. 5-170
:TRIGger:EINTerval:EVENt<x>:
SPATtern:HEXA
Sets the pattern of the serial pattern trigger in hexadecimal notation. 5-170
:TRIGger:EINTerval:EVENt<x>:
SPATtern:LATCh?
Queries all settings related to latch of the serial pattern trigger. 5-170
:TRIGger:EINTerval:EVENt<x>:
SPATtern:LATCh:POLarity
Sets the polarity of the latch trace of the serial pattern trigger or queries the
current setting.
5-171
:TRIGger:EINTerval:EVENt<x>:
SPATtern:LATCh:SOURce
Sets the latch trace of the serial pattern trigger or queries the current setting. 5-171
:TRIGger:EINTerval:EVENt<x>:
SPATtern:PATTern
Sets the pattern of the serial pattern trigger in binary notation or queries the
current setting.
5-171
:TRIGger:EINTerval:EVENt<x>:
SPIBus?
Queries all settings related to the SPI bus trigger of the event. 5-171
:TRIGger:EINTerval:EVENt<x>:
SPIBus:BITorder
Sets the bit order of the SPI bus trigger or queries the current setting. 5-171
:TRIGger:EINTerval:EVENt<x>:
SPIBus:CLOCk?
Queries all settings related to the clock of the SPI bus trigger. 5-172
:TRIGger:EINTerval:EVENt<x>:
SPIBus:CLOCk:POLarity
Sets the polarity of the clock trace of the SPI bus trigger or queries the
current setting.
5-172
:TRIGger:EINTerval:EVENt<x>:
SPIBus:CLOCk:SOURce
Sets the clock trace of the SPI bus trigger or queries the current setting. 5-172
:TRIGger:EINTerval:EVENt<x>:
SPIBus:CS?
Queries all settings related to the chip select of the SPI bus trigger. 5-172
:TRIGger:EINTerval:EVENt<x>:
SPIBus:CS:ACTive
Sets the active level of the chip select of the SPI bus trigger or queries the
current setting.
5-172
:TRIGger:EINTerval:EVENt<x>:
SPIBus:CS:SOURce
Sets the chip select trace of the SPI bus trigger or queries the current setting. 5-172
:TRIGger:EINTerval:EVENt<x>:
SPIBus:DATA<x>?
Queries all settings related to the data of the SPI bus trigger. 5-172
:TRIGger:EINTerval:EVENt<x>:
SPIBus:DATA<x>:BYTE
Sets the number of bytes of the data of the SPI bus trigger or queries the
current setting.
5-173
:TRIGger:EINTerval:EVENt<x>:
SPIBus:DATA<x>:CONDition
Sets the determination method (match or not match) of the data of the SPI
bus trigger or queries the current setting.
5-173
5.1 List of Commands
To Next Page
Loading...
