5-29
IM 701310-17E
Commands
Command Function Page
:TRIGger:ENHanced:I2CBus:ADATa:
BIT7ADdress:HEXA
Sets the 7-bit address of the I
2
C bus trigger in hexadecimal notation. 5-185
:TRIGger:ENHanced:I2CBus:ADATa:
BIT7ADdress:PATTern
Sets the 7-bit address of the I
2
C bus trigger in binary notation or queries the
current setting.
5-185
:TRIGger:ENHanced:I2CBus:ADATa:
BIT7APsub?
Queries all settings related to the 7-bit + Sub address of the I
2
C bus trigger. 5-185
:TRIGger:ENHanced:I2CBus:ADATa:
BIT7APsub:ADDRess?
Queries all settings related to the 7-bit address of the 7-bit + Sub address of
the I
2
C bus trigger.
5-185
:TRIGger:ENHanced:I2CBus:ADATa:
BIT7APsub:ADDRess:HEXA
Sets the 7-bit address of the 7-bit + Sub address of the I
2
C bus trigger in
hexadecimal notation.
5-185
:TRIGger:ENHanced:I2CBus:ADATa:
BIT7APsub:ADDRess:PATTern
Sets the 7-bit address of the 7-bit + Sub address of the I
2
C bus trigger in
binary notation or queries the current setting.
5-185
:TRIGger:ENHanced:I2CBus:ADATa:
BIT7APsub:SADDress?
Queries all settings related to the Sub address of the 7-bit + Sub address of
the I
2
C bus trigger.
5-185
:TRIGger:ENHanced:I2CBus:ADATa:
BIT7APsub:SADDress:HEXA
Sets the Sub address of the 7-bit + Sub address of the I
2
C bus trigger in
hexadecimal notation.
5-186
:TRIGger:ENHanced:I2CBus:ADATa:
BIT7APsub:SADDress:PATTern
Sets the Sub address of the 7-bit + Sub address of the I
2
C bus trigger in
binary notation or queries the current setting.
5-186
:TRIGger:ENHanced:I2CBus:ADATa:
TYPE
Sets the address type of the I
2
C bus trigger or queries the current setting. 5-186
:TRIGger:ENHanced:I2CBus:CLOCk?
Queries all settings related to the clock of the I
2
C bus trigger. 5-186
:TRIGger:ENHanced:I2CBus:CLOCk:
SOURce
Sets the clock trace of the I
2
C bus trigger or queries the current setting. 5-186
:TRIGger:ENHanced:I2CBus:DATA?
Queries all settings related to the data of the I
2
C bus trigger. 5-186
:TRIGger:ENHanced:I2CBus:DATA:
BYTE
Sets the number of data bytes of the I
2
C bus trigger or queries the current
setting.
5-186
:TRIGger:ENHanced:I2CBus:DATA:
CONDition
Sets the determination method (match or not match) of the data of the I
2
C
bus trigger or queries the current setting.
5-186
:TRIGger:ENHanced:I2CBus:DATA:
DPOSition
Sets the position for comparing the data pattern of the I
2
C bus trigger or
queries the current setting.
5-187
:TRIGger:ENHanced:I2CBus:DATA:
HEXA<x>
Sets the data of the I
2
C bus trigger in hexadecimal notation. 5-187
:TRIGger:ENHanced:I2CBus:DATA:
MODE
Enables/Disables the data conditions of the I
2
C bus trigger or queries the
current setting.
5-187
:TRIGger:ENHanced:I2CBus:DATA:
PATTern<x>
Sets the data of the I
2
C bus trigger in binary notation or queries the current
setting.
5-187
:TRIGger:ENHanced:I2CBus:DATA:
PMODe
Sets the pattern comparison start position mode of the data of the I
2
C bus
trigger or queries the current setting.
5-187
:TRIGger:ENHanced:I2CBus:DATA:
SOURce
Sets the data trace of the I
2
C bus trigger or queries the current setting. 5-187
:TRIGger:ENHanced:I2CBus:GCALl?
Queries all settings related to the general call of the I
2
C bus trigger. 5-187
:TRIGger:ENHanced:I2CBus:GCALl:
BIT7maddress?
Queries all settings related to the 7-bit master address of the general call of
the I
2
C bus trigger.
5-187
:TRIGger:ENHanced:I2CBus:GCALl:
BIT7maddress:HEXA
Sets the 7-bit master address of the general call of the I
2
C bus trigger in
hexadecimal notation.
5-188
:TRIGger:ENHanced:I2CBus:GCALl:
BIT7maddress:PATTern
Sets the 7-bit master address of the general call of the I
2
C bus trigger in
binary notation or queries the current setting.
5-188
:TRIGger:ENHanced:I2CBus:GCALl:
SBYTe (Second Byte)
Sets the second byte type of the general call of the I
2
C bus trigger or queries
the current setting.
5-188
:TRIGger:ENHanced:I2CBus:MODE
Sets the trigger mode of the I
2
C bus trigger or queries the current setting. 5-188
:TRIGger:ENHanced:I2CBus:
NAIGnore?
Queries all settings related to the NON ACK ignore mode of the I
2
C bus
trigger.
5-188
:TRIGger:ENHanced:I2CBus:
NAIGnore:HSMode
Sets whether to ignore NON ACK in high speed mode of the I
2
C bus trigger
or queries the current setting.
5-188
:TRIGger:ENHanced:I2CBus:
NAIGnore:RACCess
Sets whether to ignore NON ACK in read access mode of the I
2
C bus trigger
or queries the current setting.
5-188
:TRIGger:ENHanced:I2CBus:
NAIGnore:SBYTe (Start Byte)
Sets whether to ignore NON ACK in the start byte of the I
2
C bus trigger or
queries the current setting.
5-188
:TRIGger:ENHanced:I2CBus:
SBHSmode?
Queries all settings related to the start byte and high speed mode of the I
2
C
bus trigger.
5-189
:TRIGger:ENHanced:I2CBus:
SBHSmode:TYPE
Sets the type of the start byte or high speed mode of the I
2
C bus trigger or
queries the current setting.
5-189
:TRIGger:ENHanced:LINBus?
Queries all settings related to the LIN bus trigger or queries the current
setting.
5-189
5.1 List of Commands
To Next Page
Loading...
