Command Function Page
:TRIGger:ENHanced:LINBus:BRATe
Sets the LIN bus signal trigger bitrate (data transfer rate) or queries the
current setting.
5-189
:TRIGger:ENHanced:LINBus:SOURce
Sets the LIN bus signal trigger source or queries the current setting. 5-189
:TRIGger:ENHanced:SPATtern?
(Serial Pattern)
Queries all settings related to the serial pattern trigger. 5-189
:TRIGger:ENHanced:SPATtern:
BITRate
Sets the bit rate of the serial pattern trigger or queries the current setting. 5-189
:TRIGger:ENHanced:SPATtern:
CLEar
Clears the entire pattern of the serial pattern trigger (to don’t care). 5-189
:TRIGger:ENHanced:SPATtern:
CLOCk?
Queries all settings related to clock of the serial pattern trigger. 5-189
:TRIGger:ENHanced:SPATtern:
CLOCk:MODE
Enables/Disables the clock of the serial pattern trigger or queries the current
setting.
5-189
:TRIGger:ENHanced:SPATtern:
CLOCk:POLarity
Sets the polarity of the clock trace of the serial pattern trigger or queries the
current setting.
5-190
:TRIGger:ENHanced:SPATtern:
CLOCk:SOURce
Sets the clock trace of the serial pattern trigger or queries the current setting. 5-190
:TRIGger:ENHanced:SPATtern:CS
Enables/Disables the chip select of the serial pattern trigger or queries the
current setting.
5-190
:TRIGger:ENHanced:SPATtern:
DATA?
Queries all settings related to data of the serial pattern trigger. 5-190
:TRIGger:ENHanced:SPATtern:
DATA:ACTive
Sets the active level of the data of the serial pattern trigger or queries the
current setting.
5-190
:TRIGger:ENHanced:SPATtern:
DATA:SOURce
Sets the data trace of the serial pattern trigger or queries the current setting. 5-190
:TRIGger:ENHanced:SPATtern:HEXA
Sets the pattern of the serial pattern trigger in hexadecimal notation. 5-190
:TRIGger:ENHanced:SPATtern:
LATCh?
Queries all settings related to latch of the serial pattern trigger. 5-190
:TRIGger:ENHanced:SPATtern:
LATCh:POLarity
Sets the polarity of the latch trace of the serial pattern trigger or queries the
current setting.
5-191
:TRIGger:ENHanced:SPATtern:
LATCh:SOURce
Sets the latch trace of the serial pattern trigger or queries the current setting. 5-191
:TRIGger:ENHanced:SPATtern:
PATTern
Sets the pattern of the serial pattern trigger in binary notation or queries the
current setting.
5-191
:TRIGger:ENHanced:SPIBus?
Queries all settings related to the SPI bus trigger. 5-191
:TRIGger:ENHanced:SPIBus:
BITorder
Sets the bit order of the SPI bus trigger or queries the current setting. 5-191
:TRIGger:ENHanced:SPIBus:CLOCk?
Queries all settings related to the clock of the SPI bus trigger. 5-191
:TRIGger:ENHanced:SPIBus:CLOCk:
POLarity
Sets the polarity of the clock trace of the SPI bus trigger or queries the
current setting.
5-191
:TRIGger:ENHanced:SPIBus:CLOCk:
SOURce
Sets the clock trace of the SPI bus trigger or queries the current setting. 5-192
:TRIGger:ENHanced:SPIBus:CS?
Queries all settings related to the chip select of the SPI bus trigger. 5-192
:TRIGger:ENHanced:SPIBus:CS:
ACTive
Sets the active level of the chip select of the SPI bus trigger or queries the
current setting.
5-192
:TRIGger:ENHanced:SPIBus:CS:
SOURce
Sets the chip select trace of the SPI bus trigger or queries the current setting. 5-192
:TRIGger:ENHanced:SPIBus:
DATA<x>?
Queries all settings related to the data of the SPI bus trigger. 5-192
:TRIGger:ENHanced:SPIBus:
DATA<x>:BYTE
Sets the number of bytes of the data of the SPI bus trigger or queries the
current setting.
5-192
:TRIGger:ENHanced:SPIBus:
DATA<x>:CONDition
Sets the determination method (match or not match) of the data of the SPI
bus trigger or queries the current setting.
5-192
:TRIGger:ENHanced:SPIBus:
DATA<x>:DPOSition
Sets the pattern comparison start position of the data of the SPI bus trigger
or queries the current setting.
5-192
:TRIGger:ENHanced:SPIBus:
DATA<x>:HEXA<x>
Sets the data of the SPI bus trigger in hexadecimal notation. 5-193
:TRIGger:ENHanced:SPIBus:
DATA<x>:PATTern<x>
Sets the data of the SPI bus trigger in binary notation or queries the current
setting.
5-193
:TRIGger:ENHanced:SPIBus:
DATA<x>:SOURce
Sets the trace of the data of the SPI bus trigger or queries the current setting. 5-193
:TRIGger:ENHanced:SPIBus:MODE
Sets the wiring system of the SPI bus trigger (three-wire or four-wire) or
queries the current setting.
5-193
:TRIGger:ENHanced:TV?
Queries all settings related to the TV trigger. 5-193
5.1 List of Commands
To Next Page
Loading...
