5-31
IM 701310-17E
Commands
Command Function Page
:TRIGger:ENHanced:TV:COUPling?
Queries the trigger coupling of the TV trigger. 5-193
:TRIGger:ENHanced:TV:CUSTomize
Turns ON/OFF the sync guard function of the TV trigger or queries the
current setting.
5-193
:TRIGger:ENHanced:TV:FIELd
Sets the field of the TV trigger or queries the current setting. 5-193
:TRIGger:ENHanced:TV:FRAMe
Sets the frame skip function of the TV trigger or queries the current setting. 5-193
:TRIGger:ENHanced:TV:{HDTV|NTSC
|PAL|SDTV|USERdefine}?
Queries all settings related to the TV trigger mode. 5-194
:TRIGger:ENHanced:
TV:{HDTV|NTSC|PAL|SDTV}:
HFRejection?
(HighFrequencyREJECTION)
Queries the low pass filter (HF rejection) of the TV trigger. 5-194
:TRIGger:ENHanced:TV:{HDTV|NTSC
|PAL|SDTV|USERdefine}:LINE
Sets the line for activating the TV trigger or queries the current setting. 5-194
:TRIGger:ENHanced:TV:{HDTV|NTSC
|PAL|SDTV|USERdefine}:POLarity
Sets the input polarity of the TV trigger or queries the current setting. 5-194
:TRIGger:ENHanced:TV:LEVel
Sets the trigger level of the TV trigger or queries the current setting. 5-194
:TRIGger:ENHanced:TV:SGUard
Sets the sync guard of the TV trigger or queries the current setting. 5-194
:TRIGger:ENHanced:TV:SOURce
Sets the trigger source of the TV trigger or queries the current setting. 5-194
:TRIGger:ENHanced:TV:TYPE
Sets the input type of the TV trigger or queries the current setting. 5-194
:TRIGger:ENHanced:TV:
USERdefine:DEFinition
Sets the user-defined resolution or queries the current setting. 5-195
:TRIGger:ENHanced:TV:
USERdefine:HFRejection
(HighFrequencyREJECTION)
Sets the user-defined low pass filter (HF rejection) or queries the current
setting.
5-195
:TRIGger:ENHanced:TV:
USERdefine:HSYNc (Hsync Freq)
Sets the user-defined horizontal sync signal or queries the current setting. 5-195
:TRIGger:ENHanced:UART?
Queries all settings related to the UART signal trigger. 5-195
:TRIGger:ENHanced:UART:BRATe
Sets the UART signal trigger bit rate (data transfer rate) or queries the
current setting.
5-195
:TRIGger:ENHanced:UART:FORMat
Sets the UART signal trigger format or queries the current setting. 5-195
:TRIGger:ENHanced:UART:POLarity
Sets the UART signal trigger polarity or queries the current setting. 5-195
:TRIGger:ENHanced:UART:SOURce
Sets the UART signal trigger source or queries the current setting. 5-195
:TRIGger:ENHanced:UART:SPOint
Sets the UART signal trigger sample point or queries the current setting. 5-195
:TRIGger:ESTate?
Queries all settings related to the edge/state trigger. 5-196
:TRIGger:ESTate:EOR?
Queries all settings related to the OR trigger. 5-196
:TRIGger:ESTate:EOR:CHANnel<x>
Sets the channel polarity of the OR trigger or queries the current setting. 5-196
:TRIGger:ESTate:POLarity
Sets the polarity of the edge/state trigger or queries the current setting. 5-196
:TRIGger:ESTate:SOURce
Sets the trigger source of the edge/state trigger or queries the current
setting.
5-196
:TRIGger:HOLDoff
Sets the hold off time or queries the current setting. 5-196
:TRIGger:MODE
Sets the trigger mode or queries the current setting. 5-196
:TRIGger:POSition
Sets the trigger position or queries the current setting. 5-196
:TRIGger:SCOunt (Single(N)
Count)
Sets the number of times the trigger is to be activated when the trigger mode
is Single(N) or queries the current setting.
5-196
:TRIGger:SOURce?
Queries all settings related to the trigger source. 5-197
:TRIGger:SOURce:CHANnel<x>?
Queries all settings related to the channel of the trigger source. 5-197
:TRIGger:SOURce:CHANnel<x>:
COUPling
Sets the trigger coupling of the channel or queries the current setting. 5-197
:TRIGger:SOURce:
CHANnel<x>:HFRejection
(HighFrequencyREJECTION)
Sets the low pass filter (HF rejection) of the channel or queries the current
setting.
5-197
:TRIGger:SOURce:CHANnel<x>:
HYSTeresis
Sets the hysteresis of the channel or queries the current setting. 5-197
:TRIGger:SOURce:CHANnel<x>:
LEVel
Sets the trigger level of the channel or queries the current setting. 5-197
:TRIGger:SOURce:CHANnel<x>:
STATe
Sets the condition to be satisfied of the channel or queries the current
setting.
5-198
:TRIGger:SOURce:CHANnel<x>:
WIDTh
Sets the window trigger width of the channel or queries the current setting. 5-198
:TRIGger:SOURce:CHANnel<x>:
WINDow
Turns ON/OFF the window of the channel or queries the current setting. 5-198
:TRIGger:SOURce:EXTernal?
Queries all settings related to the external trigger. 5-198
:TRIGger:SOURce:EXTernal:LEVel
Sets the trigger level of the external trigger or queries the current setting. 5-198
5.1 List of Commands
To Next Page
Loading...
