Command Function Page
:TRIGger:SOURce:EXTernal:PROBe
Sets the probe attenuation of the external trigger or queries the current
setting.
5-198
:TRIGger:SOURce:LOGic
Sets the trigger source logic or queries the current setting. 5-198
:TRIGger:TYPE
Sets the trigger type or queries the current setting. 5-198
:TRIGger:WIDTh?
Queries all settings related to the pulse width trigger. 5-198
:TRIGger:WIDTh:MODE
Sets the determination mode of the pulse width trigger or queries the current
setting.
5-199
:TRIGger:WIDTh:POLarity
Sets the polarity of the pulse width trigger or queries the current setting. 5-199
:TRIGger:WIDTh:SOURce
Sets the trigger source of the pulse width trigger or queries the current
setting.
5-199
:TRIGger:WIDTh:TIME<x>
Sets the pulse width of the pulse width trigger or queries the current setting. 5-199
WAVeform Group
:WAVeform?
Queries all information about the waveform data. 5-200
:WAVeform:BITS?
Queries the bit length of the waveform data specified by “:WAVeform:
TRACe”.
5-200
:WAVeform:BYTeorder
Sets the transmission order when using word format of two bytes or more or
queries the current setting.
5-200
:WAVeform:END
Sets the last data point of the waveform specified by :WAVeform:TRACe or
queries the current setting.
5-200
:WAVeform:FORMat
Sets the format of the data to be transmitted or queries the current setting. 5-200
:WAVeform:LENGth?
Queries the total number of points of the waveform specified by “:WAVeform:
TRACe”.
5-200
:WAVeform:OFFSet?
Queries the offset value when converting the waveform data specified by :
WAVeform:TRACe to physical values.
5-200
:WAVeform:POSition?
Queries the vertical axis position used for converting to voltage when RBYTe
is specified with :WAVeform:FORMat.
5-200
:WAVeform:RANGe?
Queries the range value when converting the waveform data specified by :
WAVeform:TRACe to physical values.
5-200
:WAVeform:RECord
Sets the target record number for the commands in the WAVeform group or
queries the current setting.
5-200
:WAVeform:RECord? MINimum
Queries the minimum record number of the history of the target channel. 5-201
:WAVeform:SEND?
Queries the waveform data specified by “:WAVeform:TRACe”. 5-201
:WAVeform:SIGN?
Queries the existence of a sign when querying the waveform data specified
by :WAVeform:TRACe using binary data.
5-201
:WAVeform:SRATe? (Sample RATE)
Queries the sample rate of the record specified by :WAVeform:RECord. 5-201
:WAVeform:STARt
Sets the first data point of the waveform specified by :WAVeform:TRACe or
queries the current setting.
5-201
:WAVeform:TRACe
Sets the target waveform or queries the current setting. 5-201
:WAVeform:TRIGger?
Queries the trigger position of the record specified by :WAVeform:RECord. 5-201
:WAVeform:TYPE?
Queries the acquisition mode of the waveform specified by :WAVeform:
TRACe.
5-201
ZOOM Group
:ZOOM?
Queries all settings related to the waveform zoom. 5-202
:ZOOM:ALLocation<x>?
Queries all settings related to the zoom source waveform. 5-202
:ZOOM:ALLocation<x>:ALLon
Sets all waveforms to be zoomed. 5-202
:ZOOM:ALLocation<x>:TRACe<x>
Turns ON/OFF the trace you wish to zoom or queries the current setting. 5-202
:ZOOM:FORMat<x>
Sets the display format of the zoom waveform or queries the current setting. 5-202
:ZOOM:HLINkage
Turns ON/OFF the horizontal link or queries the current setting. 5-202
:ZOOM:HORizontal<x>?
Queries all settings related to the horizontal zoom. 5-202
:ZOOM:HORizontal<x>:ASCRoll?
Queries all settings related to the auto scroll function. 5-202
:ZOOM:HORizontal<x>:ASCRoll:
JUMP
Moves the zoom center position to the left or right edge of the main screen. 5-202
:ZOOM:HORizontal<x>:ASCRoll:
SPEed
Sets the auto scroll speed or queries the current setting. 5-202
:ZOOM:HORizontal<x>:ASCRoll:
STARt
Starts auto scrolling. 5-203
:ZOOM:HORizontal<x>:ASCRoll:
STOP
Stops auto scrolling. 5-203
:ZOOM:HORizontal<x>:MAG
Sets the horizontal zoom magnification or queries the current setting. 5-203
:ZOOM:HORizontal<x>:POSition
Sets the horizontal zoom center position or queries the current setting. 5-203
:ZOOM:MODE
Sets the zoom waveform display format or queries the current setting. 5-203
5.1 List of Commands
To Next Page
Loading...
