YOKOGAWA DL9040

5-57
IM 701310-17E
Commands
1
2
3
4
5
6
App
Index
:ANALysis:WPARameter<x>:LIST:VALue?
Function Queries the automated measured value of the
list display number of the waveform parameter
measurement.
Syntax
:ANALysis:WPARameter<x>:LIST:
VALue? {<NRf>|MAXimum}
<x> = 1 or 2
<NRf> = 1 to 100000
Example
:ANALYSIS:WPARAMETER1:LIST:VALUE? 1
-> :ANALYSIS:WPARAMETER1:LIST:
VALUE 1,1.000E+00
Description • If the measurement is not possible, “NAN (Not A
Number” is returned.
• If the value of the list display number is not present,
“NAN (Not A Number)” is returned.
• If MAXimum is specified, the maximum list display
number is selected.
:ANALysis:WPARameter<x>:MODE
Function Sets the mode of the waveform parameter
measurement or queries the current setting.
Syntax
:ANALysis:WPARameter<x>:MODE
{HISTogram|LIST|TRENd}
:ANALysis:WPARameter<x>:MODE?
<x> = 1 or 2
Example
:ANALYSIS:WPARAMETER1:MODE HISTOGRAM
:ANALYSIS:WPARAMETER1:MODE?
-> :ANALYSIS:WPARAMETER1:MODE HISTOGRAM
:ANALysis:WPARameter<x>:TRACe<x>?
Function Queries all settings related to the trace of the
waveform parameter measurement.
Syntax
:ANALysis:WPARameter<x>:TRACe<x>?
<x> of WPARameter<x> = 1 or 2
<x> of TRACe<x> = 1 to 8
Example
:ANALYSIS:WPARAMETER1:TRACE1?
-> :ANALYSIS:WPARAMETER1:TRACE1:AREA1:
TYPE BURST
:ANALysis:WPARameter<x>:TRACe<x>:
AREA<x>?
Function Queries all settings related to the area of the
waveform parameter measurement.
Syntax
:ANALysis:WPARameter<x>:TRACe<x>:
AREA<x>?
<x> of WPARameter<x> = 1 or 2
<x> of TRACe<x> = 1 to 8
<x> of AREA<x> = 1 or 2
Example
:ANALYSIS:WPARAMETER1:TRACE1:AREA1?
-> :ANALYSIS:WPARAMETER1:TRACE1:AREA1:
TYPE BURST
:ANALysis:WPARameter<x>:TRACe<x>:
AREA<x>:TYPE
Function Sets the waveform parameter of the waveform
parameter measurement or queries the current
setting.
Syntax
:ANALysis:WPARameter<x>:TRACe<x>:
AREA<x>:TYPE {<Parameter>}
:ANALysis:WPARameter<x>:TRACe<x>:
AREA<x>:TYPE?
<x> of WPARameter<x> = 1 or 2
<x> of TRACe<x> = 1 to 8
<x> of AREA<x> = 1 or 2
<Parameter> = {BURSt|CMEan|COUNt|CRMS|
CSDeviation|DELay|DT|DUTYcycle|FALL|
FREQuency|HIGH|HILow|LOW|MAXimum|MEAN|
MINimum|NOVershoot|NWIDth|PERFrequency|
PERiod|POVershoot|PTOPeak|PWIDth|RISE|
RMS|SDEViation|TYCInteg|TYINteg|V1|V2}
Example
:ANALYSIS:WPARAMETER1:TRACE1:AREA1:
TYPE BURST
:ANALYSIS:WPARAMETER1:TRACE1:AREA1:
TYPE? -> :ANALYSIS:WPARAMETER1:TRACE1:
AREA1:TYPE BURST
:ANALysis:WPARameter<x>:TRENd?
Function Queries all settings related to the trend display of the
waveform parameter measurement.
Syntax
:ANALysis:WPARameter<x>:TRENd?
<x> = 1 or 2
Example
:ANALYSIS:WPARAMETER1:TREND?
-> :ANALYSIS:WPARAMETER1:TREND:
HRANGE MAIN;HSPAN 1;MEASURE:CURSOR:C1:
POSITION 1.000E+00;STATE 1;:ANALYSIS:
WPARAMETER1:TREND:MEASURE:CURSOR:C2:
POSITION 2.000E+00;STATE 1;:ANALYSIS:
WPARAMETER1:TREND:MEASURE:CURSOR:DC:
STATE 1;:ANALYSIS:WPARAMETER1:TREND:
MEASURE:MODE CURSOR;:ANALYSIS:
WPARAMETER1:TREND:VERTICAL 2.000E+00,
1.000E+00
5.3 ANALysis Group