5-229
IM DLM4038-17EN
Commands
5
:SERialbus<x>:SPI:DETail:LIST:ITEM?
Function Queries all items that will be displayed in the SPI
bus signal analysis result list.
Syntax
:SERialbus<x>:SPI:DETail:LIST:ITEM?
<x> = 1 to 4
Example
:SERIALBUS1:SPI:DETAIL:LIST:ITEM?
-> :SERIALBUS1:SPI:DETAIL:LIST:IT
EM "No.,Time(ms),Data,,"
:SERialbus<x>:SPI:DETail:LIST:VALue?
Function Queries all of the data for the specified analysis
number in the SPI bus signal analysis result list.
Syntax
:SERialbus<x>:SPI:DETail:LIST:VAL
ue? {<NRf>|MAXimum|MINimum}
<x> = 1 to 4
<NRf> = See the DLM4000 Features Guide for
this information.
Example
:SERIALBUS1:SPI:DETAIL:LIST:VALUE? 0
-> :SERIALBUS1:SPI:DETAIL:LIST:
VALUE "0,0.077002,Data1,00 00 00 00
00 00 00 00,"
:SERialbus<x>:SPI:SEARch?
Function Queries all SPI bus signal search settings.
Syntax
:SERialbus<x>:SPI:SEARch?
<x> = 1 to 4
:SERialbus<x>:SPI:SEARch:ABORt
Function Aborts the SPI bus signal search.
Syntax
:SERialbus<x>:SPI:SEARch:ABORt
<x> = 1 to 4
Example
:SERIALBUS1:SPI:SEARCH:ABORT
:SERialbus<x>:SPI:SEARch:EXECute
Function Executes a SPI bus signal search.
Syntax
:SERialbus<x>:SPI:SEARch:EXECute
<x> = 1 to 4
Example
:SERIALBUS1:SPI:SEARCH:EXECUTE
:SERialbus<x>:SPI:SEARch:SELect
Function Sets which detected point to display in the SPI
bus signal search zoom window and queries the
zoom position of the detected point.
Syntax
:SERialbus<x>:SPI:SEARch:SELect {<NR
f>|MAXimum}
:SERialbus<x>:SPI:SEARch:SELect?
<x> = 1 to 4
<NRf> = 0 to 49999
Example
:SERIALBUS1:SPI:SEARCH:SELECT 1
:SERIALBUS1:SPI:SEARCH:SELECT?
-> :SERIALBUS1:SPI:SEARCH:SELECT 1.5
0000000
Description “
[:HISTory[:SEARch]:NUMBer<x>:CONDit
ion
” is set to OFF or when the value is otherwise
immeasurable, the DLM4000 returns “NAN” (not
a number).
:SERialbus<x>:SPI:SEARch:SELect?
MAXimum
Function Queries the number of detected points in the SPI
bus signal search.
Syntax
:SERialbus<x>:SPI:SEARch:SELe
ct? {MAXimum}
:SERialbus<x>:SPI:SEARch:SELect?
<x> = 1 to 4
Example
:SERIALBUS1:SPI:SEARCH:SELECT? MAXIM
UM
-> :SERIALBUS1:SPI:SEARCH:SELECT 100
Description “
[:HISTory[:SEARch]:NUMBer<x>:CONDit
ion
” is set to OFF or when the value is otherwise
immeasurable, the DLM4000 returns “NAN” (not
a number).
:SERialbus<x>:SPI:SEARch:SETup?
Function Queries all SPI bus signal search condition
settings.
Syntax
:SERialbus<x>:SPI:SEARch:SETup?
<x> = 1 to 4
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>?
Function Queries all SPI bus signal search data settings.
Syntax
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>?
<x> = 1 to 4
<y> = 1 to 2
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:BCOunt
Function Sets or queries the starting position of data
comparison for SPI bus signal searching.
Syntax
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:BCOunt {<NRf>}
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:BCOunt?
<x> = 1 to 4
<y> = 1 to 2
<NRf> = 0 to 9999
Example
:SERIALBUS1:SPI:SEARCH:SETUP:DATA1:B
COUNT 0
:SERIALBUS1:SPI:SEARCH:SETUP:DATA1:B
COUNT?
-> :SERIALBUS1:SPI:SEARCH:SETUP:DATA
1:BCOUNT 0
5.25 SERialbus Group
To Next Page
Loading...
Need help?
General
