YOKOGAWA DLM4038 - Page 263

5-230
IM DLM4038-17EN
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:CONDition
Function Sets or queries the data comparison condition
(true or false) for SPI bus signal searching.
Syntax
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:CONDition {FALSe|TRUE}
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:CONDition?
<x> = 1 to 4
<y> = 1 to 2
Example
:SERIALBUS1:SPI:SEARCH:SETUP:DATA1:C
ONDITION FALSE
:SERIALBUS1:SPI:SEARCH:SETUP:DATA1:C
ONDITION?
-> :SERIALBUS1:SPI:SEARCH:SETUP:DATA
1:CONDITION FALSE
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:DBYTe
Function Sets or queries the data size (in bytes) for SPI
bus signal searching.
Syntax
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:DBYTe {<NRf>}
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:DBYTe?
<x> = 1 to 4
<y> = 1 to 2
<NRf> = 1 to 4
Example
:SERIALBUS1:SPI:SEARCH:SETUP:DATA1:D
BYTE 1
:SERIALBUS1:SPI:SEARCH:SETUP:DATA1:D
BYTE?
-> :SERIALBUS1:SPI:SEARCH:SETUP:DATA
1:DBYTE 1
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:HEXa<z>
Function Sets the data for SPI bus signal searching in
hexadecimal notation.
Syntax
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:HEXa<z> {<String>}
<x> = 1 to 4
<y> = 1 to 2
<z> = 1 to 4
Example
:SERIALBUS1:SPI:SEARCH:SETUP:DATA1:H
EXA1 "AB"
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:MODE
Function Sets or queries the data enable/disable condition
for SPI bus signal searching.
Syntax
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:MODE {<Boolean>}
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:MODE?
<x> = 1 to 4
<y> = 1 to 2
Example
:SERIALBUS1:SPI:SEARCH:SETUP:DATA1:M
ODE ON
:SERIALBUS1:SPI:SEARCH:SETUP:DATA1:M
ODE?
-> :SERIALBUS1:SPI:SEARCH:SETUP:DATA
1:MODE 1
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:PATTern<z>
Function Sets or queries the data value for SPI bus signal
searching in binary notation.
Syntax
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:PATTern<z> {<string>}
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:PATTern<z>?
<x> = 1 to 4
<y> = 1 to 2
<z> = 1 to 4
Example
:SERIALBUS1:SPI:SEARCH:SETUP:DATA1:P
ATTERN1 "11001010"
:SERIALBUS1:SPI:SEARCH:SETUP:DATA1:P
ATTERN1?
-> :SERIALBUS1:SPI:SEARCH:SETUP:DATA
1:PATTERN1 "11001010"
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:PFORmat
Function Sets or queries the input format, which is one of
the data conditions, for SPI bus signal searching.
Syntax
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:PFORmat {BINary|HEXa}
:SERialbus<x>:SPI:SEARch[:SETup]:DAT
A<y>:PFORmat?
<x> = 1 to 4
<y> = 1 to 2
Example
:SERIALBUS1:SPI:SEARCH:SETUP:DATA1:P
FORMAT BINARY
:SERIALBUS1:SPI:SEARCH:SETUP:DATA1:P
FORMAT?
-> :SERIALBUS1:SPI:SEARCH:SETUP:DATA
1:PFORMAT BINARY
5.25 SERialbus Group