YOKOGAWA DLM4038 - Page 264

5-231
IM DLM4038-17EN
Commands
1
2
3
4
5
6
App
Index
:SERialbus<x>:TYPE
Function Sets or queries search type.
Syntax
:SERialbus<x>:TYPE {CANBus|CANFDbus|
CXPIbus|FLEXray|I2CBus|LINBus|PSI5|
SENT|SPATtern|SPIBus|UART}
:SERialbus<x>:TYPE?
<x> = 1 to 4
Example
:SERIALBUS1:TYPE CANBUS
:SERIALBUS1:TYPE?
-> :SERIALBUS1:TYPE CANBUS
:SERialbus<x>:UART?
Function Queries all UART signal analysis and search
settings.
Syntax
:SERialbus<x>:UART?
<x> = 1 to 4
:SERialbus<x>:UART:ANALyze?
Function Queries all UART signal analysis settings.
Syntax
:SERialbus<x>:UART:ANALyze?
<x> = 1 to 4
:SERialbus<x>:UART[:ANALyze]:SETup?
Function Queries all UART signal analysis bus settings.
Syntax
:SERialbus<x>:UART[:ANALyze]:SETup?
<x> = 1 to 4
:SERialbus<x>:UART[:ANALyze]:SETup:B
ITorder
Function Sets or queries the UART signal analysis bit
order.
Syntax
:SERialbus<x>:UART[:ANALyze]:SETup:B
ITorder {MSBFirst|LSBFirst}
:SERialbus<x>:UART[:ANALyze]:SETup:B
ITorder?
<x> = 1 to 4
Example
:SERIALBUS1:UART:ANALYZE:SETUP:BITOR
DER MSBFIRST
:SERIALBUS1:UART:ANALYZE:SETUP:BITOR
DER?
-> :SERIALBUS1:UART:ANALYZE:SETUP:BI
TORDER MSBFIRST
:SERialbus<x>:UART[:ANALyze]:SETup:B
RATe
Function Sets or queries the UART signal analysis bit rate
(data transfer rate).
Syntax
:SERialbus<x>:UART[:ANALyze]:SETup:B
RATe {<NRf>|USER,<NRf>}
:SERialbus<x>:UART[:ANALyze]:SETup:B
RATe?
<x> = 1 to 4
<NRf> = 1200, 2400, 4800, 9600, 19200, 38400,
57600, 115200
USER <NRf> = See the DLM4000 Features
Guide for this information.
Example
:SERIALBUS1:UART:ANALYZE:SETUP:BRA
TE 2400
:SERIALBUS1:UART:ANALYZE:SETUP:BRA
TE?
-> :SERIALBUS1:UART:ANALYZE:SETUP:BR
ATE 2400
:SERialbus<x>:UART[:ANALyze]:SETup:B
SPace
Function Sets or queries the byte space setting for UART
signal analysis.
Syntax
:SERialbus<x>:UART[:ANALyze]:SETup:B
SPace {<Time>}
:SERialbus<x>:UART[:ANALyze]:SETup:B
SPace?
<x> = 1 to 4
<Time> = See the DLM4000 Features Guide for
this information.
Example
:SERIALBUS1:UART:ANALYZE:SETUP:BSPA
CE 0.1S
:SERIALBUS1:UART:ANALYZE:SETUP:BSPA
CE?
-> :SERIALBUS1:UART:ANALYZE:SETUP:BS
PACE1.000E−01
:SERialbus<x>:UART[:ANALyze]:SETup:G
ROuping
Function Sets or queries the on/off status of grouping for
UART signal analysis.
Syntax
:SERialbus<x>:UART[:ANALyze]:SETup:G
ROuping {<Boolean>}
:SERialbus<x>:UART[:ANALyze]:SETup:G
ROuping?
<x> = 1 to 4
Example
:SERIALBUS1:UART:ANALYZE:SETUP:GROUP
ING ON
:SERIALBUS1:UART:ANALYZE:SETUP:GROUP
ING?
-> :SERIALBUS1:UART:ANALYZE:SETUP:GR
OUPING 1
5.25 SERialbus Group