YOKOGAWA DLM4038 - Page 265

5-232
IM DLM4038-17EN
:SERialbus<x>:UART[:ANALyze]:SETup:P
OLarity
Function Sets or queries the polarity setting for UART
signal analysis.
Syntax
:SERialbus<x>:UART[:ANALyze]:SETup:P
OLarity {NEGative|POSitive}
:SERialbus<x>:UART[:ANALyze]:SETup:P
OLarity?
<x> = 1 to 4
Example
:SERIALBUS1:UART:ANALYZE:SETUP:POLAR
ITY NEGATIVE
:SERIALBUS1:UART:ANALYZE:SETUP:POLAR
ITY?
-> :SERIALBUS1:UART:ANALYZE:SETUP:PO
LARITY NEGATIVE
:SERialbus<x>:UART[:ANALyze]:SETup:S
OURce
Function Sets or queries the source signal for UART signal
analysis.
Syntax
:SERialbus<x>:UART[:ANALyze]:SETup:S
OURce {<NRf>|MATH<y>|PODA<y>|PODB<y>
|PODL<y>}
:SERialbus<x>:UART[:ANALyze]:SETup:S
OURce?
<x> = 1 to 4
<NRf> = 1 to 8
<y> of MATH<y> = 1 to 4
<y> of PODA<y>, PODB<y>, PODL<y> = 0 to 7
Example
:SERIALBUS1:UART:ANALYZE:SETUP:SOUR
CE 1
:SERIALBUS1:UART:ANALYZE:SETUP:SOUR
CE?
-> :SERIALBUS1:UART:ANALYZE:SETUP:SO
URCE 1
:SERialbus<x>:UART[:ANALyze]:SETup:S
POint
Function Sets or queries the UART signal analysis sample
point.
Syntax
:SERialbus<x>:UART[:ANALyze]:SETup:S
POint {<NRf>}
:SERialbus<x>:UART[:ANALyze]:SETup:S
POint?
<x> = 1 to 4
<NRf> = 18.8 to 90.6
Example
:SERIALBUS1:UART:ANALYZE:SETUP:SPOI
NT 18.8
:SERIALBUS1:UART:ANALYZE:SETUP:SPOI
NT?
-> :SERIALBUS1:UART:ANALYZE:SETUP:SP
OINT 18.8
:SERialbus<x>:UART:DETail?
Function Queries all UART signal analysis result list
settings.
Syntax
:SERialbus<x>:UART:DETail?
<x> = 1 to 4
:SERialbus<x>:UART:DETail:DISPlay
Function Sets or queries the display mode for the UART
signal analysis result list.
Syntax
:SERialbus<x>:UART:DETail:DISPlay {F
ULL|LOWer|UPPer}
:SERialbus<x>:UART:DETail:DISPlay?
<x> = 1 to 4
Example
:SERIALBUS1:UART:DETAIL:DISPLAY FULL
:SERIALBUS1:UART:DETAIL:DISPLAY?
-> :SERIALBUS1:UART:DETAIL:DISPLAY F
ULL
:SERialbus<x>:UART:DETail:LIST:ITEM?
Function Queries all items that will be displayed in the
UART signal analysis result list.
Syntax
:SERialbus<x>:UART:DETail:LIST:ITEM?
<x> = 1 to 4
Example
:SERIALBUS1:UART:DETAIL:LIST:ITEM?
-> :SERIALBUS1:UART:DETAIL:LIST:
ITEM "No.,Time(ms),Data (HEX),
Data (ASCII),Information"
:SERialbus<x>:UART:DETail:LIST:VAL
ue?
Function Queries all of the data for the specified analysis
number in the UART signal analysis result list.
Syntax
:SERialbus<x>:UART:DETail:LIST:VAL
ue? {<NRf>|MAXimum|MINimum}
<x> = 1 to 4
<NRf> = See the DLM4000 Features Guide for
this information.
Example
:SERIALBUS1:UART:DETAIL:LIST:VAL
UE? 0
-> :SERIALBUS1:UART:DETAIL:LIST:VAL
UE"0,−0.5720,3A7469D2,":ti.",,"
:SERialbus<x>:UART:SEARch?
Function Queries all UART signal search settings.
Syntax
:SERialbus<x>:UART:SEARch?
<x> = 1 to 4
:SERialbus<x>:UART:SEARch:ABORt
Function Aborts the UART signal search.
Syntax
:SERialbus<x>:UART:SEARch:ABORt
<x> = 1 to 4
Example
:SERIALBUS1:UART:SEARCH:ABORT
5.25 SERialbus Group