YOKOGAWA DLM4038 - Page 327

5-294
IM DLM4038-17EN
:TRIGger{[:ATRigger]|:BTRigger}:SIMP
le:SLOPe
Function Sets or queries the trigger source slope setting
(polarity setting when the window is set to ON)
for edge triggering.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:SIMP
le:SLOPe {ENTer|EXIT|FALL|RISE}
:TRIGger{[:ATRigger]|:BTRigger}:SIMP
le:SLOPe?
Example
:TRIGGER:ATRIGGER:SIMPLE:SLOPE ENTER
:TRIGGER:ATRIGGER:SIMPLE:SLOPE?
-> :TRIGGER:ATRIGGER:SIMPLE:SLOPE EN
TER
Description • You can use this command/query only if
:TRIGger{[:ATRigger]|:BTRigger}:SIM
Ple:SOURce
is set to EXTernal.
• If
:TRIGger:SOURce:CHANnel<x>:WIND
ow
is set to ON, select from
{ENTer|EXIT}
,
otherwise, select from
{FALL|RISE}
.
:TRIGger{[:ATRigger]|:BTRigger}:SIMP
le:SOURce
Function Sets or queries the edge trigger source.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:SIMP
le:SOURce {<NRf>|EXTernal|LINE|PODA<
x>|PODB<x>|PODL<x>}
:TRIGger{[:ATRigger]|:BTRigger}:SIMP
le:SOURce?
<NRf> = 1 to 8
<x> of PODA<x>, PODB<x>, PODL<x> = 0 to 7
Example
:TRIGGER:ATRIGGER:SIMPLE:SOURCE 1
:TRIGGER:ATRIGGER:SIMPLE:SOURCE?
-> :TRIGGER:ATRIGGER:SIMPLE:SOURCE 1
:TRIGger{[:ATRigger]|:BTRigger}:SIMP
le:WIDTh
Function Sets or queries the edge trigger source window
width.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:SIMP
le:WIDTh {<Voltage>}
:TRIGger{[:ATRigger]|:BTRigger}:SIMP
le:WIDTh?
<Voltage> = See the DLM4000 Features Guide
for this information.
Example
:TRIGGER:ATRIGGER:SIMPLE:WIDTH 1V
:TRIGGER:ATRIGGER:SIMPLE:WIDTH?
-> :TRIGGER:ATRIGGER:SIMPLE:WIDTH 1.
000E+00
:TRIGger{[:ATRigger]|:BTRigger}:SIMP
le:WINDow
Function Sets or queries the edge trigger source window.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:SIMP
le:WINDow {<Boolean>}
:TRIGger{[:ATRigger]|:BTRigger}:SIMP
le:WINDow?
Example
:TRIGGER:ATRIGGER:SIMPLE:WINDOW ON
:TRIGGER:ATRIGGER:SIMPLE:WINDOW?
-> :TRIGGER:ATRIGGER:SIMPLE:WINDOW 1
Description You cannot use this command when
:TRIGger{[:ATRigger]|:BTRigger}:SIMP
le:SOURce
is set to EXTernal or LINE.
:TRIGger{[:ATRigger]|:BTRigger}:SPAT
tern?
Function Queries all user-defined bus signal trigger
settings.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:SPAT
tern?
:TRIGger{[:ATRigger]|:BTRigger}:SPAT
tern:BITSize
Function Sets or queries the bit length setting for user-
defined bus signal triggering.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:SPAT
tern:BITSize {<NRf>}
:TRIGger{[:ATRigger]|:BTRigger}:SPAT
tern:BITSize?
<NRf> = 1 to 128
Example
:TRIGGER:ATRIGGER:SPATTERN:BITSIZE 1
:TRIGGER:ATRIGGER:SPATTERN:BITSIZE?
-> :TRIGGER:ATRIGGER:SPATTERN:BITSI
ZE 1
:TRIGger{[:ATRigger]|:BTRigger}:SPAT
tern:BRATe
Function Sets or queries the bit rate setting for user-
defined bus signal triggering.
Syntax
:TRIGger{[:ATRigger]|:BTRigger}:SPAT
tern:BRATe {<NRf>}
:TRIGger{[:ATRigger]|:BTRigger}:SPAT
tern:BRATe?
<NRf> = 1000 to 50000000
Example
:TRIGGER:ATRIGGER:SPATTERN:BRA
TE 1000
:TRIGGER:ATRIGGER:SPATTERN:BRATE?
-> :TRIGGER:ATRIGGER:SPATTERN:BRA
TE 1000
5.34 TRIGger Group