What to do if there is a movement, but the recording is not initiated on my 360 Vision H7016 DVR?
If recording is not initiated despite movement being present on your 360 Vision DVR, and the sensitivity is set too low, set a higher sensitivity value in the recording setting.
What to do if there is no video on the monitor connected to my 360 Vision H7016 DVR?
If there's no video on the monitor connected to your 360 Vision DVR, ensure the power cable is correctly connected to the monitor. Also, check that the monitor cable is properly connected to the port on the rear panel of the DVR. If the monitor does not support some vertical resolution frequencies, change the monitor to a new one which can support over 50Hz.
Why is my remote monitoring program successfully executed, but not properly connected to my 360 Vision H7016?
If your remote monitoring program is successfully executed but not properly connected to your 360 Vision DVR, verify that the network is connected by performing a ping test. Ensure you are using a CAT 5 TPE (Category 5 Twisted-Pair Ethernet) cable and that it's correctly connected, noting that different methods apply depending on the network's connection status (cross cable or direct cable). If issues persist, test the connection by directly linking the PC and the DVR using a cross cable to isolate network environment errors. Finally, confirm that the version of the Remote Monitoring Program matches that of the system; update it from the website if necessary.
How to fix a monitored image that is displayed too bright in the monitor on a 360 Vision H7016?
If you find that the monitored image on your 360 Vision DVR is too bright, you can adjust the monitor settings to correct this. Also, check and adjust the camera iris, as it may not be properly adjusted. If the issue persists, there might be a problem with the video display or the camera's synchronous signal; in this case, inspect the video cable and connection, or try using a different camera to see if that resolves the brightness issue.
What to do if the monitored image is displayed too dark in the monitor on a 360 Vision DVR?
If the monitored image on your 360 Vision DVR appears too dark, try adjusting the monitor settings first. If adjusting the monitor doesn't solve the issue, check and adjust the camera iris, as it may not be correctly adjusted.
How to improve the color of the image in the monitor on a 360 Vision DVR?
If the color of the image on your 360 Vision DVR monitor is poor, begin by checking and correcting the monitor settings. If the issue persists, adjust the output setting values for contrast and brightness in the display settings. Should these steps not resolve the problem, the video chip may have an issue, and you should have it checked by an authorized vendor or the installer.
Why can't I connect to my 360 Vision H7016 DVR even though the remote monitoring program is executed and the Ping test is ok?
If the 360 Vision DVR remote monitoring program can be executed and the Ping test is ok, but it cannot be connected, it could be due to several reasons. First, check for IP conflicts with other equipment on the network. If removing the DVR's network cable allows the Ping test to pass, another device is likely using the same IP address; assign a different, unused IP to the DVR. Next, verify that the IP address, ID, and password settings in the Remote Monitoring Program are correct. Also, ensure that the DVR's network settings are properly configured, including the IP address, user management credentials (ID/Password/Access Right), and that the network setting per channel is enabled in the recording setup. Finally, confirm that the port numbers used by the DVR are not blocked by a firewall; ...
How to prevent recording from starting with insignificant movement on my 360 Vision H7016?
If the sensitivity is set too high and recording starts with insignificant movement on your 360 Vision DVR, try setting a lower sensitivity value in the recording settings. Also, exclude any insignificant areas from the motion detection region.
What to do if the selected channel does not light up red when I try to select the channel connected to the sensor on my 360 Vision H7016?
If the selected channel does not light up red when you try to select the channel connected to the sensor on your 360 Vision DVR, check that the recording mode is set to a sensor Recording type in the schedule setting of the relevant channel.
Why does the alarm not turn off but remains on continuously after the sensor has detected input on my 360 Vision H7016 DVR?
If the alarm on your 360 Vision DVR remains on continuously after the sensor detects input, use a multi-meter to check if the sensor output is continuously shorted when there is input. Also, adjust the output port operation time for when the sensor has detected input, as the duration of the sensor alarm may be set too long.
General safety cautions and warnings for operating the product.
Warnings indicating potential death or serious injury.
Warnings indicating potential serious or lesser injury or damage.
Warnings about tripping hazards and contact with liquids.
Cautions regarding minor injury or damage.
Detailed technical specifications of the H7016 model.
Performing various searches and navigating recorded playback.
Setting up general system parameters like date, time, and language.
Managing HDD settings, including formatting and overwriting.
Setting resolution, FPS, quality, and recording schedules.
Configuring motion detection, sensors, and alarm event actions.
Solutions for common issues with device startup and screen display.
General| Operating System | Embedded Linux |
|---|---|
| Operating Humidity | 10% to 90% |
| Channels | 16 |
| Compression | H.264 |
| Network | Ethernet |
| Operating Temperature | -10 °C to +55 °C (14 °F to 131 °F) |
| Video Input | 16 channels |
| Video Output | 1 HDMI, 1 VGA |
To Next Page
