ABB PT003888 - Tables

Operation Manual / Power2 340-H / Low-pressure stage
Tables
© Copyright 2022 ABB. All rights reserved. HZTL4053_EN Revision F March 2022
Tables
Table1: Definition of pictograms .............................. 11
Table2: Personal protective equipment to be worn
at all times ...................................................................... 15
Table3: Personal protective equipment to be worn
specific to the respective task ................................... 15
Table4: Transient pressure increase in the event of
deflagration.................................................................... 16
Table5: Operating limits ............................................. 19
Table6: Recommended inspection and replacement
intervals........................................................................... 19
Table7: Further data .................................................... 19
Table8: Weight of the low-pressure stage complete.
31
Table9: Fixing screw tightening torque (01).......... 35
Table10: Fixing screw tightening torque (05) ....... 35
Table11: Tightening torque (61003)......................... 35
Table12: Lubricating oil pressure at oil inlet up-
stream of the turbocharger ....................................... 40
Table13............................................................................ 41
Table14 ........................................................................... 41
Table15: Expected replacement intervals [h]......... 49
Table16 ........................................................................... 51
Table17........................................................................... 52
Table18: Parameters for wet cleaning of com-
pressor ........................................................................... 55
Table19: Malfunctions when starting – Delayed
start-up .......................................................................... 58
Table20: Malfunctions when starting – Vibrations.....
58
Table21: Malfunctions when starting – Rubbing of
rotating parts................................................................ 58
Table22: Malfunctions during operation – Lubricat-
ing oil pressure too low............................................... 59
Table23: Malfunctions during operation – Power2 LP
speed reductions.......................................................... 59
Table24: Malfunctions during operation – Power2
HP speed reductions ................................................... 59
Table25: Malfunctions during operation – Power2
LP speed increases ...................................................... 59
Table26: Malfunctions during operation – Power2
HP speed increases ....................................................... 60
Table27: Malfunctions during operation – Exhaust
gas temperature too high............................................ 60
Table28: Malfunctions during operation – Charge air
pressure too low............................................................ 61
Table29: Malfunctions during operation – Charge air
pressure too high .......................................................... 61
Table30: Malfunctions during operation – Com-
pressor 1 contamination .............................................. 62
Table31: Malfunctions during operation – Com-
pressor 2 contamination.............................................. 62
Table32: Malfunctions during operation – Blow-by
too high ........................................................................... 62
Table33: Surging of the low-pressure or high-pres-
sure stage........................................................................ 63
Table34: Malfunctions when stopping – Runout
noises............................................................................... 64
Table35: Malfunctions when stopping – Runout
time too short ................................................................ 64
Table36: Speed measurement – poor signal amp-
litude ................................................................................ 65
Table37: Speed measurement – speed too high .... 65
Table38: Speed measurement – speed too low...... 65
Table39: Swivel lifting eyes......................................... 68
Table40: Weights of the assemblies......................... 69
Table41: Press-off screws to be used....................... 70
Table42: Permissible clearances N and R................. 72
Table43: Permissible clearances A and B................. 80
Table44: Nozzle ring compression PD...................... 81
Table45: Tightening torque (51007) ......................... 84
Table46: Tightening torque (79041) ......................... 85
Table47: Tightening torque (72011) ......................... 86
Table48: Permissible clearances N and R................. 87
Table49: Tightening torque (72020)......................... 88
Table50: Tightening torques (51009, 61003).......... 90
Table51: Tightening torques [Nm] ............................ 91
Table52: Tightening torques (51007) ....................... 94
Page 121 / 122Page 121 / 122