Home
ADS
Measuring Instruments
TRITON+
Page 24
ADS TRITON+ - Page 24
535 pages
Manual
Save Page as PDF
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
1-16 A
DS
TRITON+
Manu
al
Long Range Depth (CS6) ATE
X, IECEx, CSA, UKCA Certific
ation Label
Inclino
me
ter
ATEX
, IEC
Ex
, C
SA,
UKCA C
er
tifi
cation
L
abe
l
Sampler Cable ATEX, IECEx, CS
A, UKCA Certification Label
23
25
Table of Contents
Main Page
default chapter
4
Table of Contents
4
Chapter 1 Introduction
9
Intrinsic Safety
10
TRITON+ System Certification
11
Installation and IS Considerations
14
Specific Conditions of Use
14
Other Conditions for Safe Use
16
Maintenance Restrictions
17
Warnings, Certifications, Cellular Modem Compliance, and Conformity
18
Changes or Modifications
18
Control Drawing
19
European ATEX Hazardous Area Compliance
21
Iecex (International Electrotechnical Commission Explosive) Hazardous Area Compliance
26
CSA Hazardous Area Compliance
28
Declaration of Conformity
36
Product Warranty
38
New Product Warranty
38
Out-Of-Warranty Product Repairs
38
Troubleshooting Fee
39
Shipping
39
Service
40
Chapter 2 System Overview
41
TRITON+ Flow Monitor
45
Communications
45
Processor Board
46
Connector Ports
48
Power
51
Sensors
55
Av|Gated Sensor
56
Av|Max Sensor
58
Long Range Depth Sensor
60
Paradepth Sensor
62
Paraflow Sensor
64
Peak Combo Sensor
67
Ultrasonic Depth Sensor
70
Surface Combo Sensor
71
Inclinometer Sensor
74
I/O and Modbus Capability
75
Analog Inputs and Outputs
75
Digital Inputs and Outputs
76
Modbus
76
Project Organization Checklist
77
Chapter 3 Communication
78
Cellular-Based Wireless Communication Overview
80
Activating the SIM Card
82
Installing the Antenna
84
Gathering Parts and Supplies
84
Installing the Wireless Antenna
87
Installing (Replacing) the SIM Card
93
Connecting the Antenna to the Monitor
97
Connecting to the Monitor in the Field
99
Connecting Directly to the Monitor
100
Connecting to the Monitor through the Expac
101
Chapter 4 Configuration and Activation
103
Hardware and Software Compatibility
104
Starting Qstart XML
104
XML Parameters
105
Configuring the Monitor Location
109
Create and Configure the Monitor Location
109
Configure the Monitoring Point(S)
112
Assigning and Editing Devices
117
Activating the Monitor
190
Setting up the RTU to Retrieve the Current Data through Modbus
192
Designating the Data for Retrieval
192
Verifying the Modbus Output Data
192
Running Sensor Diagnostics
194
Performing Confirmations
198
Collecting Data from the Monitor
202
Upgrading the Monitor Firmware
205
Viewing Diagnostic and Data Logs
206
Chapter 5 Sensor Installation and Connection
207
Investigating Site Characteristics
210
Flow Hydraulics
210
Pipe and Manhole Characteristics
211
Installing the Sensors in the Pipe
213
Standard Installation
213
Special Installations for Av|Gated, Av|Max, Peak Combo, Surface Combo, or Ultrasonic Depth Sensors
244
Installing the Sensors in the Manhole Structure
265
Long Range Depth Sensor Installation
265
Topside Retrieval System (Applies to Paradepth and Paraflow Sensors)
286
Securing the Sensor Cables in the Pipe and Manhole
301
Connecting the Sensors and Sampler to the Monitor
303
Securing the Dryer Tube to the Monitor
305
Chapter 6 External Power
307
Installation
308
DC Power Requirements and Consumption
309
Mounting the XIO or XBUS
310
Mounting the Recommended Power Supply
312
Mounting the Expac
316
Wiring the AC Power Source to the Recommended Power Supply
321
Wiring the Power Supply to the Expac
324
Running the Ground Wires
328
Wiring the Expac/Xbus/Xio to the Monitor
335
Final Instructions
342
Chapter 7 Monitor Installation
344
Mounting the Monitor on Manhole Rung
346
Mounting the Monitor to the Manhole Wall
347
Mounting the Monitor to the Manhole Rim
350
Chapter 8 Inclinometer
356
Installing the Inclinometer
357
Inclinometer Data
361
Chapter 9 Analog and Digital Inputs and Outputs
364
Analog Inputs
366
Connecting a Third-Party Instrument to an Analog Input on the XIO
366
Analog Outputs
371
Connecting a Third-Party Device to an Analog Output on the XIO
371
Digital Inputs
376
Connecting a Third-Party Device to a Digital Input on the XIO
376
Digital Outputs
379
Connecting a Third-Party Device to a Digital Output on the XIO
379
Chapter 10 Modbus
383
Establishing a Modbus Connection
384
Setting up a Serial Connection
384
Setting up a Wireless Connection
391
Configuring the Monitor for Modbus Applications
392
Modbus Data Registers
393
Register Addresses for Entity Data
393
Chapter 11 Maintenance and Troubleshooting
399
Maintaining the System Components
400
Gathering Replacement Parts and Supplies
400
Inspecting the Monitor
401
Inspecting, Cleaning, and Handling the Sensors
418
Replacing the SIM Card
422
Replacing the Fuses in the Monitor
433
Interpreting the Diagnostic LED Codes on the Expac
440
Troubleshooting
442
General Monitor Problems
443
Communication Problems
447
Long Range Depth Subsystem
451
Ultrasonic Depth Subsystem
453
Upward Depth Subsystem
458
Peak Velocity Subsystem
461
Surface Velocity Subsystem
464
Pressure Depth Subsystem
466
Temperature Subsystem
467
External Power, I/O, and Modbus Subsystems
469
Appendix A Specifications
473
TRITON+ Flow Monitor (ADS P/N 8000-FST-IM
473
Intrinsically-Safe Sensors
478
USB Serial Interface (ADS P/N 8000-0337
492
Expac (ADS P/N 8000-0377
493
Power Supply (ADS P/N 508293
494
XBUS (ADS P/N 8000-0427
495
XIO (ADS P/N 8000-0400
496
Appendix B Part Numbers
498
Appendix C Monitor Activity Codes
504
Appendix D Third-Party Logger Support
508
Telog Ru-33 or
509
Ayyeka Wavelet 4R
511
Appendix E Sampler Cable Connections and Specifications
513
TRITON+ Sampler Cable Illustrations
514
Sampler Cable Connection Options and Specifications
514
Related product manuals
ADS ECHO
2 pages
To Next Page
