Ammann AV 70 X - Reguirements on Drivers Qualification; Drivers Liabilities

23AV 70 X
OPERATION MANUAL
2.1.2. Reguirements on Driver’s Qualication
Only a driver trained under ISO 7130 and other local and na- •
tional regulations designed for drivers of this group of ma-
chines may operate the Roller (Compacter).
With no licence only the one who learns driving the Machi-
•
ne for the purpose of getting preliminary practice with the
approval of User may drive the Machine, and such person
has to be under direct and continuous surveillance of pro-
fessional teacher or trainer.
Licence holder is liable to take due care of the licence, and
•
when requested, put it forward to the control authorities.
Licence holder can make no registrations, changes or corre-
•
ctions in the licence card.
He/she is liable to promptly report his/her licence loss to the
•
authority that issued this licence.
Driving the Roller alone may be performed by an employee
•
mentally and physically t, over 18 years old, who is:
a) assigned by machine manufacturer for the assembly,
testing and presentation of the Machine, for training
the drivers, whereas he/she must be made familiar with
safety work regulations in force at the workplace
or
b) assigned by Constructional Supplier to operate (carry out
maintenance) and is evidently trained and acquainted
with, or owns professional competence to operate and
drive under special regulations (machinist licence, etc.).
Machine driver must undergo training and examination con-
•
cerning work safety regulations at least 1x every 2 years.
2.1.3. Driver’s Liabilities
Before starting to operate the Machine the driver will be •
liable to get familiar with the guidelines given in the docu-
mentation delivered with the Machine, with safety precauti-
ons in particular, and observe these thoroughly. This applies
as well to the personnel in charge of maintenance, adjust-
ments and repairs of the Machine.
Do not drive the Roller unless made familiar with all the Ma-
•
chine functions, working and operating elements, and un-
less knowing exactly how to control the Machine.
Follow safety signs located on the Machine, and keep them
•
in legible condition. Replace or add those impaired or mis-
sing ones.
Before work commencement the driver must get familiar
•
with the workplace environment, i.e. with the slopes, utility
line system, with necessary types of workplace protections
with regard to the environment (noise, etc.).
When nding out any health hazard, life hazard to persons,
•
hazard to property, failures, during hardware accidents, or
when nding symptoms of such hazards during operati-
on, the driver must, unless able to remove such hazard by
himself/herself, stop his/her work and secure the Machine
against undesired starting, communicate this to a person
accountable, and depending on chances, notify all the per-
sons exposed to such hazard.
Before Machine operation startup the driver will be liable to
•
get familiar with the records and operation deviations found
out in course of the previous work shift.
When you nd out any hazard to health or life of persons,
•
property hazard, failure, or upon technology equipment ac-
cident, or when nding any symptoms of such hazards in
course of operation, then the driver, unless able to elimina-
te such hazard by himself/herself, must stop the work and
secure the machine against any undesirable start; please at-
tach “MACHINE REPAIR” [OPRAVA STROJE] warning sign onto
steering wheel as depicted in Section called “Safety signs
used on the machine“, report this to the person in charge,
and if possible, notify all persons exposed to such danger.
During work with the Machine the driver must be fastened
•
with the seat belt. The seat belt and its mounting shall not
be damaged!
When driver nds any defect during operation he/she must
•
immediately stop the Machine, secure it safely against un-
desired ignition.
During operation the driver shall follow the Machine run
•
and record any defects found in the Operation Logbook.
Driver shall keep his/her Operation Logbook designed to
•
maintain records about Machine handover between the dri-
vers, about the defects or repairs in course of operation, to
write down major events during work shift.
Prior turning on the engine the controls have to be in their
•
zero position, no persons may stay within dangerous reach
of the Machine.
Indicate each Machine startup via an acoustic or light signal
•
and this always before igniting the Machine engine.
Conrm brake function and steering function before star-
•
ting to run the Machine.