Barco DP-1500 - Page 48

162 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

5. Lenses & lens holder

44 R59770091 DP-1500 06/01/2009

Table of Contents

Default Chapter3
- Software License Agreement3
- Disposal Information4
- Table of Contents5
1 Operating Conditions7
- Certiﬁcation8
- Physical Environment9
- Heat Dissipation/Cooling10
- Input Power11
- Initial Inspection12
- Mutual Agreement13
2 Safety Instructions15
- General Considerations16
- Restricted Access Location17
- Electrical Safety18
- Heat and Fire Hazards19
- Safety on Installation20
- Protection from Ultraviolet Radiation21
- Protection on Servicing22
- Safety on Cleaning23
- Safety on Shipping24
3 Mechanical Set up of the DP-150025
- Unpacking the Projector26
- Positioning the DP-1500 at Port Window28
- Projector Tilting29
- Installation of the Exhaust System31
4 Electrical Set up of the DP-150033
- Power Requirements34
- Connecting the Main AC Power35
5 Lenses & Lens Holder37
- Available Lenses38
- Lens Selection39
- Lens Formulas40
- Lens Removal41
- Lens Installation42
- Lens Shift, Zoom & Focus44
- Scheimpﬂug Adjustment45
6 Lamp & Lamp House49
- Introduction50
- Removal of the Lamp House51
- Removal of the Xenon Bulb Lamp53
- Installation of the Xenon Bulb Lamp56
- Installation of the Lamp House61
- Resetting the Lamp Parameters63
- Realignment of the Lamp in Its Reﬂector64
7 Input & Communication Unit67
- Introduction68
- Local Keypad of the DP-1500 Projector69
- Communication Ports of the DP-1500 Projector70
- About General Purpose Inputs & Outputs (GPIO)72
- Source Input Ports of the DP-1500 Projector74
8 Communicator Touch Panel75
- Introduction76
- Installing the Touch Panel Interface78
- Reposition the Touch Panel Interface80
9 Starting up81
- Switching on the DP-1500 Projector82
- Switching off the DP-1500 Projector83
10 Projector Registration85
- Introduction86
- Download the Certiﬁcate File87
- Registration of New Projector88
- Update Registration of an Existing Projector94
11 Maintenance95
- Cleaning the Lens96
- Cleaning the Exterior of the Projector97
- Replacement of the Dust Filter on the Front Side98
- Replacement of the Dust Filter on the Bottom Side100
- Replacement of the Dust Filter on the Top Side101
- Pressure Veriﬁcation of the Liquid Cooling Circuit102
12 Servicing103
- Removal of the Input & Communication Unit104
- Installation of the Input & Communication Unit105
- Convergence (with Extenders)107
- Convergence (Old System)115
- Authorization to Clear Security Warning125
13 Removal and Installation of Projector Covers127
- Removal of the Lamp Cover128
- Removal of the Input Cover129
- Removal of the130
- Removal of the Side Cover131
- Removal of the Rear Cover132
- Removal of the Top Cover133
- Open the Sealed Compartment134
- Close the Sealed Compartment135
- Installation of the Top Cover136
- Installation of the Rear Cover137
- Installation of the Side Cover138
- Installation of the139
- Installation of the Input Cover140
- Installation of the Lamp Cover141
Speciﬁcations143
- Speciﬁcations of the DP-1500145
Dimensions147
- Dimensions of the DP-1500148
- Centre of Gravity of the DP-1500149
- Dimensions of the Universal Pedestal150
Pin Conﬁgurations151
- Pin Conﬁgurations of the Communication Ports152
- Ethernet Port152
- Pin Conﬁgurations of the Inputs153
Order Info155
- Spare Part Order Info157
Glossary159
Index161

Related product manuals

Preview: Barco DP K-19B Series

Barco DP K-19B Series

Preview: Barco DP K-32B Series

Barco DP K-32B Series

Preview: Barco DP2K-12C

Preview: Barco DP2K-19B

Preview: Barco DP2K-23B

Preview: Barco DP2K-20CLP

Barco DP2K-20CLP

Preview: Barco DP2K-C Series

Barco DP2K-C Series

Preview: Barco DP2K-S Series

Barco DP2K-S Series