Barco DP2K-S Series

Barco DP2K-S Series

153 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

11. Convergence

76 R5977692 DP2K-S SERIES 10/12/2012

Table of Contents

Default Chapter5
- Table of Contents5
1 Welcome7
- About this Manual8
2 Safety9
- General Considerations10
- Important Safety Instructions11
3 Getting Started15
- Installation Requirements16
- Unpacking the Projector18
- Initial Inspection20
4 Installation Process21
- Installation Process Overview22
5 Physical Installation23
- Positioning the DP2K-S Series Projector at Port Window24
- Installation of the Exhaust System27
- Connecting the Projector with the Power Net29
6 Lenses & Lens Selection31
- Available Lenses32
- Lens Selection33
- Lens Installation34
- Lens Removal35
- Lens Shift, Zoom & Focus36
7 Input & Communication39
- Introduction40
- Local Keypad41
- Projector Status43
- Integrated Cinema Processor (ICP)44
- HD-SDI Input Module (Optional)45
- Integrated Media Block/Server (Optional)48
- Cinema Controller49
8 Communicator Touch Panel51
- Introduction52
- Installing the Touch Panel Interface54
- Repositioning the Touch Panel Interface56
9 Starting up57
- Switching the DP2K-S Series Projector on58
- Switching the DP2K-S Series Projector off59
10 Scheimpflug61
- Scheimpflug Introduction62
- Scheimpflug Adjustment64
- Fixation of the Lens Holder Front Plate66
- Back Focal Length Adjustment68
11 Convergence71
- Convergence Controls72
- Preparing for Convergence Adjustment74
- Converging the Blue Pattern Onto the Red Pattern75
- Converging the Green Pattern Onto the Red Pattern77
- Closing off the Light Processor Compartment79
12 Lamp House & Lamp Replacement81
- Introduction82
- Supported Xenon Lamps84
- Lamp Replacement Process85
- Removal of the Lamp House87
- Removal of the Xenon Lamp from the Lamp House88
- Installation of the Xenon Lamp into the Lamp House93
- Installation of the Lamp House98
- Resetting the Lamp Parameters99
- Realignment of the Lamp in Its Reflector102
13 Preventative Maintenance Actions105
- Month Maintenance Actions106
- Month Maintenance Actions107
- Lamp Change Maintenance Actions108
14 Maintenance Procedures109
- Check the Large Dust Filter110
- Check the Small Dust Filter112
- Vacuum Cleaning of the Dust Filters114
- Washing and Drying the Dust Filters115
- Cleaning the Lens116
- Cleaning the Exterior of the Projector117
- Cleaning the UV Blocker of the Lamp House118
- Cleaning the Reflector of the Lamp House119
- Authorization to Clear Security Warning on the Projector120
15 Removal and Installation of the Projector Covers121
- Removal of the Lamp House Cover122
- Removal of the Rear Cover123
- Removal of the Top Cover124
- Removal of the Left Side Cover125
- Removal of the Top Cover Plate of the Light Processor Compartment126
- Removal of the Side Cover Plate of the Light Processor Compartment128
- Installation of the Side Cover Plate of the Light Processor Compartment129
- Installation of the Top Cover Plate of the Light Processor Compartment130
- Installation of the Left Side Cover132
- Installation of the Top Cover133
- Installation of the Rear Cover134
- Installation of the Lamp House Cover135
Specifications137
- Specifications of the DP2K-10S Series138
- Dimensions of the DP2K-S Series Projector139
- Dimensions of the Universal Pedestal140
Pin Configurations141
- About General Purpose Inputs & Outputs (GPIO)142
- Pin Configurations of the Communication Ports144
Environmental Information145
- Disposal Information146
- Rohs Compliance147
- Hazards149
- Production Address150
Index151

Related product manuals

Preview: Barco DP2K-12C

Preview: Barco DP2K-19B

Preview: Barco DP2K-23B

Preview: Barco DP2K-20C

Preview: Barco DP2K-20CLP

Barco DP2K-20CLP

Preview: Barco DP2K-36BLP

Barco DP2K-36BLP

Preview: Barco DP2K-10SLP

Barco DP2K-10SLP

Preview: Barco DP2K-E series

Barco DP2K-E series

Preview: Barco DP2K-C Series

Barco DP2K-C Series

Preview: Barco DP2K SLP Series

Barco DP2K SLP Series