EasyManuals Logo

Baxi Fourtech Series User Manual

Baxi Fourtech Series
Go to English
264 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #58 background imageLoading...
Page #58 background image
58
926.116.5 - en
INSTRUCTIONS FOR FITTERS
The DHW lters and the lters of the heating circuit are housed in special extractable cartridges. The cartridge of the he-
ating circuit is located on the return of the heating (gure 16F), the cartridge of the DHW circuit is on the cold water input
(gure 16E). To clean the lters, proceed as described below:
r UVSOPGGUIFFMFDUSJDQPXFSTVQQMZUPUIFCPJMFS
r UVSOPGGUIF%)8JOMFUUBQ
r ESBJOUIFXBUFSPVUPGUIFIFBUJOHDJSDVJUUVSOJOHPOUBQ"JOàHVSF
r SFNPWFUIFDMJQ&'GSPNUIFàMUFSBTJMMVTUSBUFEJOUIFàHVSFBOEUBLFPVUUIFDBSUSJEHF&'DPOUBJOJOHUIFàMUFS
taking care not to apply excessive force;
r UPFYUSBDUUIFDBSUSJEHFPGUIFIFBUJOHàMUFSZPVNVTUàSTUSFNPWFUIFNPUPSPGUIFXBZWBMWF(àHVSF
r FMJNJOBUFBOZJNQVSJUJFTBOEEFQPTJUTGSPNUIFàMUFS
r SFQPTJUJPOUIFàMUFSJOUIFDBSUSJEHFBOEQVUJUCBDLJOUPJUTIPVTJOHTFDVSJOHJUXJUIUIFDMJQ
r UPDIBOHFUIF%)8/5$TFOTPSTFFàHVSF%
IMPORTANT
when replacing and/or cleaning the O-rings on the hydraulic assembly, only use Molykote 111 as a lubricant, not oil or grease.
29. CLEANING THE FILTERS
The DHW circuit can be cleaned without removing the water-water heat exchanger if the assembly is tted with the special
tap (available on request) located on the DHW outlet.
To clean, proceed as follows:
r 5VSOPGGUIF%)8JOMFUUBQ
r %SBJOUIF%)8TZTUFNCZPQFOJOHBIPUXBUFSUBQ
r 5VSOPGGUIF%)8PVUMFUUBQ
r 3FNPWFUIFDMJQ&JOàHVSF
r 3FNPWFUIFàMUFS&àH
If the special tap is not supplied, dismount the water-water heat exchanger, as described in the next section, and clean it
separately. Remove the scale from the seat and relative NTC sensor tted on the DHW circuit (gure 16D).
To clean the exchanger and/or DHW circuit, use Cillit FFW-AL or Benckiser HF-AL.
30. REMOVING SCALE FROM THE DHW CIRCUIT
The stainless steel plate-type water-water heat exchanger is easily disassembled with a screwdriver by operating as
described below:
r ESBJOUIFTZTUFNKVTUUIFCPJMFSJGQPTTJCMFUISPVHIUIFESBJOUBQ
r ESBJOUIF%)8TZTUFN
r SFNPWFUIFUXPTDSFXTBUUIFGSPOUTFDVSJOHUIFXBUFSXBUFSIFBUFYDIBOHFSBOEQVMMJUPVUàHVSF#
31. DISMOUNTING THE WATER-WATER HEAT EXCHANGER

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Baxi Fourtech Series and is the answer not in the manual?

Baxi Fourtech Series Specifications

General IconGeneral
BrandBaxi
ModelFourtech Series
CategoryBoiler
LanguageEnglish

Related product manuals