EasyManua.ls Logo

Beta RR 125 LC User Manual

Beta RR 125 LC
93 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
ENGINE SPECIFICATIONS
EAS20290
ENGINE SPECIFICATIONS
Engine
Engine type Liquid cooled 4-stroke, SOHC
Displacement 124.7 cm³
Cylinder arrangement Forward-inclined single cylinder
Bore × stroke 52.0 × 58.6 mm (2.05 × 2.31 in)
Compression ratio 11.20 :1
Standard compression pressure (at sea level) 550 kPa/600 r/min (5.5 kgf/cm²/600 r/min, 78.2
psi/600 r/min)
Minimummaximum 480620 kPa (4.86.2 kgf/cm², 68.388.2 psi)
Starting system Electric starter
Fuel
Recommended fuel Premium unleaded gasoline only
Fuel tank capacity 8.5 L (2.25 US gal, 1.87 Imp.gal)
Fuel reserve amount 1.6 L (0.42 US gal, 0.35 Imp.gal)
Engine oil
Lubrication system Wet sump
Type SAE 10W-30, SAE 10W-40, SAE 15W-40, SAE
20W-40 or SAE 20W-50
Recommended engine oil grade API service SG type or higher, JASO standard
MA
Engine oil quantity
Total amount 1.15 L (1.22 US qt, 1.01 Imp.qt)
Without oil filter element replacement 0.95 L (1.00 US qt, 0.84 Imp.qt)
With oil filter element replacement 1.00 L (1.06 US qt, 0.88 Imp.qt)
Oil filter
Oil filter type Paper
Oil pump
Oil pump type Trochoid
Inner-rotor-to-outer-rotor-tip clearance Less than 0.150 mm (0.0059 in)
Limit 0.23 mm (0.0091 in)
Outer-rotor-to-oil-pump-housing clearance 0.1300.180 mm (0.00510.0071 in)
Limit 0.25 mm (0.0098 in)
Oil-pump-housing-to-inner-and-outer-rotor
clearance 0.060.11 mm (0.00240.0043 in)
Limit 0.18 mm (0.0071 in)
Relief valve operating pressure 39.278.4 kPa (0.390.78 kgf/cm², 5.711.4 psi)
Pressure check location Check bolt on cylinder head body

Table of Contents

Question and Answer IconNeed help?

Do you have a question about the Beta RR 125 LC and is the answer not in the manual?

Beta RR 125 LC Specifications

General IconGeneral
Displacement124.8 cc
Fuel SystemElectronic Fuel Injection
IgnitionElectronic
LubricationWet sump
ClutchWet multi-disc
Transmission6-speed
Final DriveChain
Seat Height920 mm
Fuel Tank Capacity7.5 liters
Starting SystemElectric
Front SuspensionHydraulic fork with ø41 mm shaft
Front Brake260 mm disc
Rear BrakeSingle disc, 220 mm
Engine TypeLiquid-cooled, 4-stroke, single cylinder

Summary

Engine Specifications

Engine Mechanicals

Specifications for engine type, displacement, bore, stroke, valve train, piston, and crankshaft.

Engine Systems

Specifications for fuel, lubrication, ignition, clutch, and transmission systems.

Tightening Torques

General Torque Specifications

Specifies tightening torques for standard ISO thread pitch fasteners and assembly procedures.

Engine Procedures

Valve Clearance Adjustment

Procedure for measuring and adjusting valve clearance on a cold engine.

Compression Pressure Measurement

Steps to measure engine compression pressure and diagnose issues.

Engine Oil Level and Change

Procedures for checking engine oil level and changing engine oil and filter.

Cylinder Head Service

Cylinder Head Removal

Step-by-step instructions for removing the cylinder head assembly.

Cylinder Head Installation

Steps for installing the cylinder head, including bolt tightening.

Camshaft and Rocker Arm Service

Valves and Valve Springs Service

Cylinder and Piston Service

Generator and Starter Clutch Service

Electric Starter Service

Clutch Service

Oil Pump Service

Shift Shaft Service

Balancer Gears Service

Crankcase Service

Crankshaft Service

Removal

Procedure for removing the crankshaft and balancer.

Transmission Service

Thermostat Service

Water Pump Service

Electrical Components Testing

Related product manuals