Binder KB - Dimensions KB; KB-UL 400

To Next Page

To Previous Page

KB / KB-UL (E4 + E6) 10/2021 page 135/147

23.10 KB / KB-UL 400 dimensions

[mm]

Main Page

Table of Contents2
Safety6
Personnel Qualification6
Operating Manual6
Legal Considerations6
Intellectual Property7
Structure of the Safety Instructions7
Signal Word Panel7
Safety Alert Symbol8
Pictograms8
Word Message Panel Structure9
Localization / Position of Safety Labels on the Chamber9
Type Plate10
General Safety Instructions on Installing and Operating the Chambers11
Intended Use13
Foreseeable Misuse14
Residual Risks15
Operating Instructions16
Measures to Prevent Accidents16
Chamber Description18
Chamber Overview19
Instrument Panel20
Lateral Control Panel with Main Power Switch and Optional Equipment - KB / KB-UL 240 / 400 / 720 (E6)21
Chamber Rear - KB / KB-UL 53 / 115 (E4)22
Completeness of Delivery, Transportation, Storage, and Installation23
Unpacking, and Checking Equipment and Completeness of Delivery23
Guidelines for Safe Lifting and Transportation24
Storage24
Location of Installation and Ambient Conditions25
Installation of the Chamber27
Spacers for Wall Distance - KB / KB-UL 240 / 400 / 720 (E6)27
Mounting the Flexible Tilt Protection Kit28
Electrical Connection29
Start up30
Functional Overview of the T4.12 Chamber Controller30
Menu Structure31
General Menu31
Quick Menu33
User" Menu33
Operating Modes34
Activating the "Control Off" Mode or Change to "Fixed Value" Operating Mode34
Performance During and after Power Failure36
Information36
Configuration of Optional Equipment37
Switching on or off the Optional Zero-Voltage Relay Control Outputs38
Functional Test of the Optional Alarm Output39
Switching on or off the Optional Object Temperature Display39
Set-Point Entry in "Fixed Value" Operating Mode40
Set-Point Ranges40
Entering the Set-Points Via "Quick Menu40
Entering the Set-Points Via General Menu42
Time Programs43
Starting and Running an Existing Time Program45
Cancelling a Running Time Program48
Creating a New Time Program49
Section Handling51
Temperature Setpoint52
Section Duration52
Repeating One or Several Sections Within a Time Program53
Tolerance Range54
Set-Point Ramp and Set-Point Step Modes56
Switching on or off the Optional Zero-Voltage Relay Outputs58
Calling up the Next Parameter58
Saving the Time Program and Leaving the Program Editor60
Program Interruption61
Deleting a Time Program63
Week Programs64
Starting and Running an Existing Week Program65
Cancelling a Running Week Program67
Creating a New Week Program68
Section Handling70
Temperature Setpoint71
Day of the Week71
Time of the Day72
Activity of the Shift-Point73
Switching on or off the Optional Zero-Voltage Relay Outputs73
Calling up the Next Parameter74
Saving the Week Program and Leaving the Program Editor76
Deleting a Week Program77
Key Lock78
Directly Activating the Key Lock Function79
Automatic Key Lock79
Changing the Password for Unlocking the Key Lock81
General Controller Settings82
Setup Wizard83
Date and Time Settings83
Selecting the Menu Language of the T4.12 Controller85
Setting Display Brightness85
Changing the Temperature Unit86
Defining the Data Recording Rate86
Factory Reset87
Network Configuration87
Display of the Entire Network Configuration91
Display and Entry of the Chamber Configuration - for Service Purpose91
Data Transfer Via Usb Interface92
Exporting Data to USB Drive92
Importing Data from USB Drive93
Notifications and Alarms94
Notifications Overview94
Alarms Overview94
Alarm Status95
Confirming a "Set" Alarm96
Alarm Configuration and Overview97
List of Active Alarms97
History - List of All Alarms98
Activating, Deactivating, and Testing the Alarm Buzzer99
Activating / Deactivating All Alarm Functions99
Event List100
Graphical Display of the Measured Values101
Setting the Sampling Rate101
Defining the Display Range102
Selecting the Parameters103
Temperature Safety Devices103
Over Temperature Protective Device (Class 1)103
Overtemperature Safety Controller (Temperature Safety Device Class 3.1)103
Safety Controller Modes104
Setting the Safety Controller104
Over- and Undertemperature Safety Controller (Temperature Safety Device Class 3.3) (Option)108
Safety Controller Modes108
Setting the Over- and Undertemperature Safety Controller109
Defrosting During Refrigerating Operation112
Options113
APT-COM™ 4 Multi Management Software (Option)113
Data Logger Kit (Option)113
Interior Lighting113
Zero-Voltage Relay Alarm Output (Option)113
Zero-Voltage Relay Control Outputs (May be Available Via BINDER INDIVIDUAL Customized Solution)114
Object Temperature Display with Flexible Pt 100 Temperature Sensor (Option)115
Cleaning and Decontamination116
Cleaning116
Decontamination / Chemical Disinfection117
Maintenance and Service, Troubleshooting, Repair, Testing119
General Information, Personnel Qualification119
Maintenance Intervals, Service119
Simple Troubleshooting120
Sending the Chamber Back to BINDER Gmbh123
Disposal123
Disposal of the Transport Packing123
Decommissioning124
Disposal of the Chamber in the Federal Republic of Germany124
Disposal of the Chamber in the Member States of the EU Except for the Federal Republic of Germany125
Disposal of the Chamber in Non-Member States of the EU126
Technical Description127
Factory Calibration and Adjustment127
Over Current Protection127
Definition of Usable Volume127
Technical Data128
Equipment and Options (Extract)130
Spare Parts and Accessories (Extract)131
KB / KB-UL 53 Dimensions132
KB / KB-UL 115 Dimensions133
KB / KB-UL 240 Dimensions134
KB / KB-UL 400 Dimensions135
KB / KB-UL 720 Dimensions136
Certificates and Declarations of Conformity137
EU Declaration of Conformity137
Certificate for the GS Mark of Conformity of the "Deutsche Gesetzliche Unfallversicherung E.V." (German Social Accident Insurance) DGUV140
Contamination Clearance Certificate142
For Chambers Located Outside USA and Canada142
For Chambers in USA and Canada145

Binder KB - Dimensions KB; KB-UL 400

Table of Contents

Related product manuals