To Next Page
N
Nicole StoneAug 25, 2025
Why is my Bizerba SC II printer not printing?
- MmreevesAug 26, 2025
If your Bizerba Scales printer won't print, it might be because the print bar is open. Make sure to close the print bar correctly.
Why is my Bizerba SC II printer not printing?
If your Bizerba Scales printer won't print, it might be because the print bar is open. Make sure to close the print bar correctly.
How to fix Bizerba SC II display if it does not illuminate?
If the display of your Bizerba Scales does not illuminate, the issue might be due to a lack of supply voltage or incorrect display settings. First, ensure the power cable is properly connected and the mains switch is turned on. If the display remains dark, reset the display settings by confirming the key sequence: +.
What does 'Apply weight' mean on Bizerba Scales?
If your Bizerba Scales display 'Apply weight' during sales, registration is only performed for a weight-dependent PLU after a load change.
What does 'No ticket data existing' mean on Bizerba SC II Scales?
If your Bizerba Scales display 'No ticket data existing' during sales when entering the ticket no. with the 'Enter ticket no.' key, check that the entered ticket no. is correct and re-enter it.
What does 'No overwriting' mean on Bizerba SC II Scales?
If your Bizerba Scales display 'No overwriting' during sales, it means the PLU is locked in PLU maintenance for price overwriting. Switch on price overwrite.
What does 'No extra text under this number!' mean on Bizerba SC II Scales?
If your Bizerba Scales display 'No extra text under this number!' during sales when calling a general text with the 'Call gen. text' key, check the entered text number. Also, in the 'Data maintenance' / 'Texts' / 'Gen. texts' menu, check the entry for the applied text number.
What does 'Cashier has not determined a Cash reg. (POS) act.!' mean on Bizerba Scales?
If your Bizerba Scales display 'Cashier has not determined a Cash reg. (POS) act.!' for cashier reports, in 'Configuration', the setting 'Compulsory cash reg. POS act.' must be set in the 'Cash reg.' menu.
What to do if Bizerba Scales display 'Cash drawer X is not connected'?
If your Bizerba Scales display 'Cash drawer X is not connected' in cash register mode, check the set values of the operator used in 'Data maintenance' / 'Operator data'. Also, check the SC II connection cable for the cash drawer.
What does 'Preset tare error' mean on Bizerba SC II?
If your Bizerba Scales display 'Preset tare error' during sales, it means when entering a known tare, the tare value may not exceed the lower division range on a two-interval scale. Enter the tare in the lower division range only.
What does 'Unit price too large' mean on Bizerba Scales?
If your Bizerba Scales display 'Unit price too large' during sales, check the settings for sales limits in 'Configuration' / 'Device settings' / 'Sales limits'.
General| Display | LCD |
|---|---|
| Readability | 1 g / 2 g / 5 g |
| Material | Stainless steel |
| Power Supply | 100-240 V AC, 50/60 Hz |
| Operating Temperature | -10°C to +40°C |
| Connectivity | Ethernet, RS232 |
| Application | Retail, industrial |
| Platform Size | 300 x 400 mm / 400 x 500 mm |
Instructions are integral part of device, must be kept accessible.
Device operated by trained personnel familiar with instructions.
Various symbols used in instructions with their meanings.
Source of danger with high risk of imminent danger to persons!
Source of danger with medium risk of possible danger to persons!
Source of danger with low risk of possible danger to persons!
SC II available with linerless or label printer; SC II 7'' with TFT display.
Bizerba offers a wide range of accessories for the device.
High-quality device for convenient counter sales, use only as intended.
Example of an identification plate.
Detailed explanation of each inscription on the scale's identification plate.
Information related to scale verification requirements specific to Germany.
Software ID and update logbook checked during verification by approval officer.
Lists EMC directives and standards relevant to the device.
Lists low voltage directive and safety standards for IT equipment.
Requirements for power supply installation and connection to Bizerba devices.
Measures for mains power supply interference suppression.
Identifies hazards like wrong supply voltage and energized electronics when switched off.
How to transport and store the device in its original packaging.
Information on putting the device into operation and initial setup.
Steps for placing the scale out of operation for a long period.
How to adjust display settings like brightness and contrast.
Steps for unpacking and assembling the device.
How to level the scale using foot screws and a spirit level.
Procedure for checking the power supply connection.
Location of the power switch for SC II 100 and SC II 800 models.
Example of the scale display showing weight, unit price, selling price, and icons.
Explanation of symbols and their meanings in the display.
Details on transparent modules and insert-foils for membrane keyboards.
Instructions for opening and closing the printer lid and side cover.
What happens when the ticket roll is empty and how paper is rejected.
Diagrams and labels for feeding label paper in the SC II 800.
Diagrams and labels for feeding ticket paper in the SC II 800.
Step-by-step guide to powering on the scale.
Information about automatic keyboard check and error messages.
How to cancel a mistakenly called function and return to the initial display.
How to erase individual characters during value entry.
How to switch on the Bakery device (SC II 100 K/B).
How to operate the SC II 100 K/B with weight values.
Procedures for direct PLU access via PLU keys or second keyboard level.
Steps for indirect PLU call-up using configuration and confirmation.
How to call up a PLU and register it using an operator key.
How to input or overwrite the unit price after a PLU call-up.
How to tare unknown values (empties) and applicable rules.
Procedure for manually entering traceability numbers for origin data.
How manual articles can be multiplied in self-service mode.
Explanation of graduated price and 'No Charge' pricing for items.
How to enforce mandatory piece number entry for each PLU.
Configuration and operation for 'Manual-weighed' PLU type.
Table listing common faults, their causes, and elimination steps.
Table of text messages, causes, and remedies.
Cleaning instructions must be observed during installation, operation and maintenance.
Safety warnings and instructions for cleaning the device.
How to clean the thermal strip using specific Bizerba products.
How to clean the label printer from glue residue.
Procedure for testing the accuracy of the weight display.
Diagrams showing the dimensions of SC II 800, SC II 100, and SC II 200.
Requirements for electrical power supply compliance.
