EasyManuals Logo

Bosch SOLUTION 6000 Installation Guide

Bosch SOLUTION 6000
172 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #47 background imageLoading...
Page #47 background image
Solution 6000
Installation Manual Access Programming
5-5
Bosch Security Systems 07/14 BLCC610I
2) Swipe the token card past the reader. As you swipe
the token, the reader will sound a single beep to
confirm that the token has been learnt.
To add token for Ur1
John Smith present new
token
Press OK or MENU
i
Note
If the Add Token command is initiated from a keypad
that does not have a built in reader, you will need to
select a reader from the list before proceeding. Swipe
the Token at the selected reader.
i
Note
In previous versions, systems configured to use a
CM796B Wiegand to RS485 LAN Interface Module
with a PR100B Proximity Reader would successfully
allow the user to learn tokens via the PR100B however
presenting the same token to other compatible
LAN or keypads readers on the system would fail to
operate.
In version 2.14, this has been corrected so that
tokens added via the PR100B Proximity Reader
can now be used across all compatible proximity
readers.
i
Note
In previous versions, when adding consecutive tokens
via the reader, the system would always display the
first user that doesn't already have a token assigned
rather than the next user in sequence.
In version 2.15, when adding consecutive tokens,
after adding user x, the keypad will now return to
user x + 1.
Access > Token >
Delete Token
-
MENU 1-2-1
This menu allows the installer or master user to delete an
existing users token ID.
1) Enter [MENU] + [1] + [2] + [1] and use the up and
down arrows to highlight the user in the list then
press [OK]. The keypad will only display users that
have tokens assigned to them.
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press
 OK or MENU
2) Press [OK] to delete the token or press [MENU] to
exit without saving.
Press OK to Delete Token
For Ur1
John Smith
Press OK or MENU
Access > Token >
Token Status
-
MENU 1-2-2
This menu allows the installer or master user to identify
which user a token has been assigned to. You will need to
have the token in order to do the test. This menu can only
be performed at a prox keypad.
1) Enter [MENU] + [1] + [2] + [2]. The keypad will
prompt you to swipe the token to be checked.
Present Token to be
Identified
Press OK or MENU
2) Present the token to the keypad, you will hear a
confirmation beep and the display will show the
token status.
Token belongs to Ur2
Debbie Smith
Press OK or MENU
3) To exit, press [OK] or [MENU].
Access > Token >
Edit Token
-
MENU 1-2-3
This menu allows the installer or master user to view or
change the token ID for any user.
1) Press [MENU] + [1] + [2] + [3] and use the up and
down arrows to highlight the user in the list, then
press [OK].
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press
 OK or MENU
2) The keypad will display the current token ID of the
user selected.
Edit Token Ur1
0000000000
Press 0-9 OK to SAVE
3) Press [OK] to save and exit or press [MENU] to exit
without saving.

Table of Contents

Other manuals for Bosch SOLUTION 6000

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Bosch SOLUTION 6000 and is the answer not in the manual?

Bosch SOLUTION 6000 Specifications

General IconGeneral
Partitions8
System TypeHybrid wired/wireless security system
KeypadsUp to 16
CommunicationPSTN, optional IP module, optional GSM/GPRS module
Arming ModesStay, Away
Power Supply16.5VAC
Backup Battery12V 7Ah
Operating Temperature0°C to +50°C

Related product manuals